valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
The LED turns from blinking to permanent. Note: You cannot disconnect Bluetooth in the talking state but end a call. English Installation Warning .This installation information is designed for professional installers with knowledge of automobile electrical safety sys- tems and is not intended for non-technical, do-it-yourself indi- viduals. It does not contain instructions on the electrical installa- tion and avoidance of potential harm to air bag, anti-theft and ABS braking or other systems necessary to install this product. Any attempt to install this product in a motor vehicle by anyone other than a professional installer could cause damage to the electrical safety systems and could result in serious personal injury or death. .If your car is equipped with air bag and/or anti-theft systems, specific procedures may be required for connection and discon- nection of the battery to install this product. Before attempting installation of this electronic component against the manufac- turer’s recommendation, you must contact your car dealer or manufacturer to determine the required procedure and strictly follow their instructions. FAILURE TO FOLLOW THE PROCEDURE MAY RESULT IN THE UNINTENDED DEPLOYMENT OF AIR BAGS OR ACTIVATION OF THE ANTI-THEFT SYSTEM RESULTING IN DAMAGE TO THE VEHI- CLE AND PERSONAL INJURY OR DEATH. . Installation Hardware q CY-BT100U Main Unit Q'ty: 1 w Switch Unit (2 m) Q'ty: 1 e Microphone with Bracket (5 m) Q'ty: 1 r System-up Connecting cable (3 m) Q'ty: 1 t Double-sided Tape (12 x 55 mm) Q'ty: 2 y Double-sided Tape (15 x 30 mm) Q'ty: 1 u Cable Clamp Q'ty: 5 English q Attach the Main unit q and the Switch Unit w with the Caution double-sided tape t y. .Make sure that wiring is completed before installation. Switch Unit w .Do not install the product where it is exposed to strong vibrations or is unstable. Avoid slanted or strongly curved surfaces for installation. If the installation is not stable, the unit may fall down while driving and this can lead to an accident or injury. Peel off the back papers Peel off the back papers 1 Remove the cable from the battery negative w Secure the microphone with bracket e. terminal. e Secure all connection cables with Cable Clamp u. 2 Connect all cables of the Hands-Free Kit fea-Attach the Microphone with turing Bluetooth® technology. Bracket e sun visor etc. 3 Secure the Main unit q, Switch Unit w and Microphone with Bracket e. Fix the cable with the Cable Clamp u. Main Unit q Sun visor by clipping on the 4 Reconnect the Battery Cable. Wiring Connection between the Hands-Free Kit featuring Bluetooth® technology and head unit Head unit (e.g. CQ-C8403U, Option) Microphone with Bracket e Switch Unit w Main Unit q System-up connecting cable r English Connection among the Hands-Free Kit featuring Bluetooth® technology and two or more devices Head unit/Expansion module connection cable (supplied with CY-EM100U) Expansion Module (CY-EM100U, Option) System-up connecting cable r Switch Unit w Head unit (e.g. CQ-C8403U, Option) iPod Direct Cable for iPod (CA-DC300U, Option) Microphone with Bracket e Main Unit q Troubleshooting If You Suspect Something Wrong Check and take steps as described below. If the described suggestions do not solve the problem, it is recommended to take the unit to your nearest authorized Panasonic Servicenter. The product should be serviced only by qualified personnel. Please refer the checking and the repair to professionals. Panasonic shall not be liable for any accidents arising out of neglect of checking the unit or your own repair after your checking. Problem Warning .Do not use the unit in an irregular condition, for exam- ple, without sound, or with smoke or a foul smell, which can cause ignition or electric shock. In case that such conditions occur, immediately stop using this unit and consult your dealer. .Never try to repair the unit by yourself because it is dan- gerous to do so. The paired mobile phone cannot be automatically reconnected. Possible cause a Possible solution The Bluetooth function of the mobile phone is disabled. (Some mobile phones are turned off in a predetermined time in the power-saving mode or the like.) . Refer to the operating instructions for the mobile phone and change the setting. The mobile phone is selected to the setting so that automatic reconnection is not permitted. . Refer to the operating instructions for the mobile phone and change the setting. Bluetooth connection is lost by key operation. . Establish Bluetooth connection again by key operation. . If Bluetooth connection is not successfully established, delete “CY-BT100” from the mobile phone pairing list, and try pairing again. English Problem Failure to pair a mobile phone Possible cause a Possible solution There is the other wireless equipment near the unit. . Switch off the other wireless equipment or keep it away from these bluetooth units. The mobile phone (or main unit) is touched or covered by metal objects. Or the mobile phone is h...