Produttore : Charmglow
File Size : 457.88 kb
File Nome : 505c362c-33fe-47c8-bbe1-7133e21f6ca2.pdf
|
Facilità d'uso
ASSEMBLER/INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE CONSUMER. CONSUMER/USER: READ ALL THESE INSTRUCTIONS AND KEEP THEM IN A SAFE PLACE FOR FUTURE REFERENCE. TOOLS REQUIRED #2 PHILLIPS SCREWDRIVER PLIERS HAMMER BOX END WRENCH WARNING: THE EDGES OF SHEET METAL PARTS CAN CAUSE INJURY IF NOT HANDLED WITH CARE. USE EXTREME CAUTION! ENGINEERING CODE CCF11244 IMPORTANT! OUTDOOR COOKING TO ENSURE PROPER GAS FLOW, BURNER 4101 Howard Bush Neosho, Mo. 64850 CONTROL VALVES MUST BE “OFF” BEFORE INTERNET SITE: OPENING THE GAS CYLINDER VALVE. 11412239 11412239 (Pg. 2) (4) Qty A CK CK CK CK LEFT RIGHT BACK FRONT 4 1 1 4 LABEL 4 1 BACK LEFT A1 WARNING: Combustion by-products produced when using this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. CK 3 17 16 3 B1 18 RIGHT FRONT B2 17 16 3 18 18 16 17 FRONT LEFT B TAP AXLE (3) INTO ONE HUB CAP (17) WITH A HAMMER. INSERT THE AXLE INTO THE BOTTOM HOLES IN THE LEFT LEGS. 3 17 16 3 B1 18 RIGHT FRONT B2 17 16 3 18 18 16 17 FRONT LEFT B TAP AXLE (3) INTO ONE HUB CAP (17) WITH A HAMMER. INSERT THE AXLE INTO THE BOTTOM HOLES IN THE LEFT LEGS. 11412239 (Pg. 3) 11412239 (Pg. 4) KR JU JU JU JU (4) Qty(2) Qty BACK 42 C C2 C1 42 49 BACK KR SOUP CAN NOT INCLUDED JU DD DD DD DD D 25 FRONT JU JU 27 25 D1 32 D2 NOTE VALVE AND HOSE ORIENTATION DD DD LEFT (4) Qty (2) Qty DD DD DD DD D 25 FRONT JU JU 27 25 D1 32 D2 NOTE VALVE AND HOSE ORIENTATION DD DD LEFT (4) Qty (2) Qty 11412239 (Pg. 5) 11412239 (Pg. 6) 43 45 K K 48 48a E 45 48a 48 SPRING TAB NOTCH E1 48a (2) Qty. NOTE: THE SPRING TAB MUST BE ON TOP AND SNAP INTO NOTCH ON ELECTRODE. CORRECT SPRING POSITION ELECTRODE TIP 43 45 K K 48 48a E 45 48a 48 SPRING TAB NOTCH E1 48a (2) Qty. NOTE: THE SPRING TAB MUST BE ON TOP AND SNAP INTO NOTCH ON ELECTRODE. CORRECT SPRING POSITION ELECTRODE TIP 11412239 (Pg. 7) (2) Qty (1) Qty 43 BACKF DZ DZ DZ F2 UNDERNEATH VIEW VENTURI TUBES ORIFICE SMALL HEAT SHIELD IMPORTANT: POSITION THE BURNER VENTURI TUBES OVER THE VALVE ORIFICES.THE ORIFICES MUST BE VISIBLE THROUGH THE VENTURI TUBE’S AIR OPENINGS. HEAT SHIELD NOT SHOWN FOR CLARITY 47 LB LEFT F3 LARGE HEAT SHIELD 47a F1 NOTE: THE BURNER WILL HOLD THE HEAT SHIELD IN PLACE. (2) Qty (1) Qty 43 BACKF DZ DZ DZ F2 UNDERNEATH VIEW VENTURI TUBES ORIFICE SMALL HEAT SHIELD IMPORTANT: POSITION THE BURNER VENTURI TUBES OVER THE VALVE ORIFICES.THE ORIFICES MUST BE VISIBLE THROUGH THE VENTURI TUBE’S AIR OPENINGS. HEAT SHIELD NOT SHOWN FOR CLARITY 47 LB LEFT F3 LARGE HEAT SHIELD 47a F1 NOTE: THE BURNER WILL HOLD THE HEAT SHIELD IN PLACE. 11412239 (Pg. 8) 26 G TEST THE IGNITER: A SPARK SHOULD APPEAR AT ELECTRODE TIP. IF THE SPARK DOES NOT APPEAR: - CHECK THE WIRE CONNECTION TO THE IGNITER. -CHECK THE ELECTRODE INSTALLATION IN DETAIL E. MAIN BURNER ELECTRODE WIRE THE ELECTRODE TIP IS LOCATED ON THE BURNER ASSEMBLED IN THE BOTTOM CASTING. CK CK CK CK CK CK H1 9 9 9 BACK RIGHT (12) Qty 14 14 H BACK RIGHT REPEAT FOR LEFT SIDE TABLE 26 G TEST THE IGNITER: A SPARK SHOULD APPEAR AT ELECTRODE TIP. IF THE SPARK DOES NOT APPEAR: - CHECK THE WIRE CONNECTION TO THE IGNITER. -CHECK THE ELECTRODE INSTALLATION IN DETAIL E. MAIN BURNER ELECTRODE WIRE THE ELECTRODE TIP IS LOCATED ON THE BURNER ASSEMBLED IN THE BOTTOM CASTING. CK CK CK CK CK CK H1 9 9 9 BACK RIGHT (12) Qty 14 14 H BACK RIGHT REPEAT FOR LEFT SIDE TABLE (2) Qty (2) Qty (2) Qty (2) Qty (2) Qty VE WO 55 J J2 (2) Qty 56 BF BF WO WO VE VE WA 58 WH J1WA WH 60 60 DZ DZ (2) Qty (2) Qty (2) Qty (2) Qty (2) Qty VE WO 55 J J2 (2) Qty 56 BF BF WO WO VE VE WA 58 WH J1WA WH 60 60 DZ DZ 11412239 (Pg. 9) 11412239 (Pg. 10) 65 L 65 TO CENTER THE RACK, SLIGHTLY BEND THE PIVOT WIRES TO ADJUST FOR A TIGHT FIT. L1 62 63K 61 IMPORTANT: EVENLY SPACE THE CERAMIC BRIQUETTES (62) ON TOP OF THE ROCK GRATE.DO NOT USE OR SUBSTITUTE CHARCOAL IN A GAS GRILL. PIVOT WIRES 11412239 (Pg. 11) 78 M 1 S T 2 N D M1 THE OUTLET VALVE MUST FACE THE GRILL FRONT. 27 GAS CYLINDER VALVE TYPE 1 NIPPLE OUTLET VALVE IMPORTANT! TO ENSURE PROPER GAS FLOW, BURNER CONTROL VALVES MUST BE "OFF" BEFORE OPENING THE GAS CYLINDER VALVE. M2 WARNING: DURING ASSEMBLY OF GRILL AND WHEN ATTACHING OR REPLACING THE L.P. GAS CYLINDER, INSURE THAT THE GAS SUPPLY HOSE IS FREE OF KINKS AND/ OR DAMAGE AND IS AT LEAST 3” AWAY FROM HOT SURFACES SUCH AS THE GRILL CASTING. M3 78 M 1 S T 2 N D M1 THE OUTLET VALVE MUST FACE THE GRILL FRONT. 27 GAS CYLINDER VALVE TYPE 1 NIPPLE OUTLET VALVE IMPORTANT! TO ENSURE PROPER GAS FLOW, BURNER CONTROL VALVES MUST BE "OFF" BEFORE OPENING THE GAS CYLINDER VALVE. M2 WARNING: DURING ASSEMBLY OF GRILL AND WHEN ATTACHING OR REPLACING THE L.P. GAS CYLINDER, INSURE THAT THE GAS SUPPLY HOSE IS FREE OF KINKS AND/ OR DAMAGE AND IS AT LEAST 3” AWAY FROM HOT SURFACES SUCH AS THE GRILL CASTING. M3 11412239 (Pg. 12) LIMITED WARRANTY Sunbeam Outdoor Cooking (“Sunbeam”) warrants that this product will be free from defects in material and workmanship. This warranty applies to the following parts...