Log:
valutazioni - 2, GPA: 3 ( )

Istruzioni per l'uso Blue Rhino, Modello GBC831WB-C

Produttore : Blue Rhino
File Size : 8.5 mb
File Nome : 0aa46889-0952-e864-05cd-2d2e4f98c15a.pdf
Lingua di insegnamento: enfr
Vai a scaricare



Facilità d'uso


Do not touch metal parts of grill until it has completely cooled (about 45 min.) to avoid burns, unless you are wearing protective gear (pot holders, gloves, BBQ mittens, etc.). When cooking, fire extinguishing materials shall be readily accessible. In the event of an oil grease fire, do not attempt to extinguish with water. Use type BC dry chemical fire extinguisher or smother with dirt, sand or baking soda. Do not install or use in or on boats or recreational vehicles. Do not use grill in high winds. Never lean over the grill when lighting. Do not leave a lit grill unattended, especially keep children and pets away from grill at all times. Do not attempt to move grill when in use. Allow the grill to cool before moving or storing. Storage of grill indoors is permissible only if the tank is disconnected, removed from the grill and properly stored outdoors. Always open grill lid carefully and slowly as heat and steam trapped within grill can severely burn you. Do not attempt to disconnect the gas regulator from the tank or any gas fitting while the grill is in use. Always place your grill on a hard non-combustible, level surface. An asphalt or blacktop surface may not be acceptable for this purpose. Move gas hoses as far away as possible from hot surfaces and dripping hot grease. Keep all electrical cords away from a hot grill. Do not use grill for indoor cooking or heating. TOXIC fumes can accumulate and cause asphyxiation. After a period of storage and/or nonuse, check for leaks, burner obstructions and inspect for any abrasion, wear, cuts to the hose. Failure to open lid while igniting the grill’s burners, or not waiting 5 minutes to allow the gas to clear if the grill does not light, may result in an explosive flame-up. If grill is not in use, the gas must be turned off at the supply tank. Never operate grill without heat plates installed. Always use a meat thermometer to ensure food is cooked to a safe temperature. Please use protective gloves when assembling this product. Do not force parts together as this can result in personal injury or damage to the product. Never cover entire cooking area with aluminum foil. Deaths, serious injury or damage to property may occur if the above is not followed exactly. page no. Exploded View Parts List 1 Lid Handle Bar 55-08-115 2 Left Lid Handle Support 55-08-116 3 Rght Lid Handle Support 55-08-117 4 Temperature Gauge 55-15-207 5 Warming Rack 55-08-118 6 Cooking Grid (2) 55-08-119 7 Lid 55-08-120 8 Heat Plate (3) 55-08-121 9 Side Burner Grid 55-15-199 10 Grill Body Assembly 55-08-122 11 Main Burner (3) 55-07-371 12 Right Side Shelf 55-08-123 13 Side Burner 55-08-124 14 Left Side Shelf 55-08-125 15 Main Burner Control Knob Support (3) 55-08-126 16 Main Burner Control Knob (3) 55-08-127 17 Igniter Button 55-07-387 18 Regulator/Hose Assembly 55-08-128 19 Left Side Shelf Front Panel 55-08-129 20 Grease Cup Support 55-07-379 21 Grease Cup 55-08-130 22 Right Side Shelf Front Panel 55-08-131 23 Side Burner Control Knob Support 55-08-132 24 Side Burner Control Knob 55-08-133 25 Leg A (2) 55-08-134 26 Leg B (2) 55-08-135 27 Cart Frame Support (2) 55-08-136 28 Lighting Rod 55-07-396 29 LP Gas Tank Heat Plate 55-08-137 30 Top Front Panel 55-08-138 31 Rear Cart Frame Support 55-08-139 32 Cart Frame Support Wire A 55-08-140 33 Front Condiment Basket 55-08-141 34 LP Gas Tank Retainer Wire 55-08-142 35 Bottom Front Panel 55-08-143 36 Left Foot Assembly 55-08-144 37 Cart Frame Support Wire B (2) 55-08-145 38 Right Foot Assembly 55-08-146 39 Wheel (2) 55-15-211 40 Hub Cap (2) 55-15-170 41 Axle 55-08-147 1 3 2 4 5 6 6 7 8 9 10 11 12 13 14 15 18 19 22 23 16 21 17 24 27 20 27 25 28 29 26 25 30 31 26 32 33 34 35 39 36 41 38 37 40 Hardware A Screw M4x10 Nickel Plated Phillips Truss Head 4 pcs B Screw M6x16 Nickel Plated Phillips Truss Head 46 pcs C Screw M6x25 Nickel Plated Phillips Truss Head 2 pcs D Nut M5 Zinc Plated 4 pcs E Nut M10 Zinc Plated 2 pcs F Wing Nut M6 Steel 6 pcs G Washer o6.4 Nickel Plated 20 pcs H Lock Washer o6.4 Nickel Plated 18 pcs I AA Battery 1 pc Tools Required for Assembly (Included) #2 Phillips Head Screwdriver M5 - M10 Wrench 2 pcs 2 Assemble Left Cart Frame Bx 4 Dx 2 Gx 2 1 DO NOT RETURN PRODUCT TO STORE. For assistance call 1.800.762.1142 toll free. Please have your owner’s manual and serial number available for reference. Note: The serial number can be found on the back of the cart assembly. For Easiest Assembly: • To avoid losing any small components or hardware, assemble your product on a hard level surface that does not have cracks or openings. • Clear an area large enough to layout all components and hardware. • When applicable, tighten all hardware connections by hand first. Once the step is completed go back and fully tighten all hardware. • Follow all steps in order to properly assemble your product. To complete assembly you will need: • (1) Leak Detection Solution (Instructions on how to make solution are included in the “Operating Instructions” sect...


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie