valutazioni - 2, GPA: 4 ( )

Produttore : Bazooka File Size : 6.8 mb File Nome : Lingua di insegnamento:

Strip one end of the wire to crimp on a barrier spade. Loosen the +12V screw terminal and insert the power wire with the barrier spade and tighten. Use caution to make sure no stray wire stands come in contact with surrounding terminals causing short circuits. Run the wire directly to the positive terminal of the car's battery. Make sure to use an in-line fuse within 12” of the car's battery to protect the electrical system and amplifier against short circuits and/or power surges. Connect the ground terminal of the amplifier to the car's chassis. For the ground connection, use an 4 to 8 gauge wire (black) to connect to the terminal marked GND and then connect it to the car's chassis. Try to keep the length of the cable as short as possible, preferably less than 6". Also make sure that the point on the car where the connection is to be made is free of paint and dirt. Connect the remote terminal of the amplifier to a switchable +12V source. This connection allows the amplifier to be turned on and off with the power control of the radio. If the radio has a REMOTE output terminal, connect it to the amplifier's terminal marked REMOTE (using a 16 gauge wire or heavier). Now when the radio is turned on, the amplifier will automatically turn on. This connection can also be made to the radio’s Power Antenna wire. IMPORTANT! Before making any connections, disconnect the car’s battery until the installation is completed to avoid possible damage to the electrical system. ENGLISH 94.7 GAIN GAIN BASS BOOST X-OVER X-OVER BASS BOOST X-OVER X-OVER LINE IN LINE IN CH1 CH3 CH1 CH3 CH2 CH4 CH1 / CH2 CH3 / CH4 CH2 CH4 HIGH INPUT HIGH INPUT MIN MAX 50Hz 250Hz 50Hz 250Hz MIN MAX 6dB 0dB 12dB LPF FLATHPF LPFFLATHPF 6dB 0dB 12dB GND GND GAIN SUBSONIC VOLUME PHASE BASS BOOST FILTER REMOTE X-OVER LINE IN LINE OUT MIN MAX 50Hz 250Hz OFF ON 0 180 6dB LPF FLAT 0dB 12dB LEFT RIGHT HIGH INPUT GND GAIN SUBSONIC PHASE BASS BOOST VOLUME REMOTE X-LINE IN LINE OUT MIN MAX 50Hz OFF ON 0 180 6dB 0dB 12dB LEFT RIGHT HIGH INPUT GND 8 SIGNAL CONNECTIONS Connect the RCA output of the head unit (AM/FM cassette player, CD, or DAT) to the RCA input terminals of the amplifier. To make these connections, we recommend high quality RCA cables, which are available at your local car audio retailer. Run signal wires away from electrical wires to avoid possibility of induced noise from the car's electrical system (i.e. popping noises or engine noise). Please note that when making these connections the signal inputs correspond with the speaker outputs. Optional full range line out connection to additional amplifiers in the system. L R R L L R L R ELA465 SIGNAL CONNECTIONS ELA SIGNAL CONNECTIONS 1300, ELA1500, & ELA1800 ELA265, ELA1190, ELA2100 & ELA2150 SIGNAL CONNECTIONS ENGLISH ELA AMPLIFIERS FRONT REAR L R R L GAIN SUBSONIC VOLUME PHASE BASS BOOST FILTER REMOTE X-OVER LINE IN LINE OUT MIN MAX 50Hz 250Hz OFF ON 0 180 6dB LPF FLAT 0dB 12dB LEFT RIGHT HIGH INPUT GND GAIN SUBSONIC VOLUME PHASE BASS BOOST FILTER REMOTE X-OVER LINE IN LINE OUT MIN MAX 50Hz 250Hz OFF ON 0 180 6dB LPF FLAT 0dB 12dB LEFT RIGHT HIGH INPUT GND 9 High Level inputs have been included to connect the amplifier to a radio without low-level outputs (i.e. factory radio). This connection will allow you to connect directly to the speaker output of the radio with out the need of an external adapter. Determine the type of radio you have and make one of the following connections. HIGH LEVEL CONNECTIONS (OPTIONAL) CAUTION! Before making any connections determine the type of radio to avoid possible damage to amplifier and/or radio. TWO CHANNEL CONNECTIONS: FLOATING GROUND RADIO (MOST COMMON TYPE) ELA1190, ELA1500 & ELA1800 RIGHT + RIGHT - LEFT - GREEN LEFT + GREEN/BLACK (NOT USED) GRAY/BLACK ...

Scarica la tua

Per scaricare, digitare 2 cifre :