valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
6 Specifications.....................................................................6 • To improve the sound field If the speakers are facing a solid wall or glass door, etc., it is recommended to furnish the wall with materials that absorb sounds, for example by hanging up thick curtains, to prevent reflections and standing waves. • To use the speakers without any trouble Thank you for purchasing a JVC speaker system. – Do not reproduce sounds at so high a volume that they Before you begin using these speakers, please read the are distorted; otherwise, the speakers may be damaged instructions carefully to be sure you get the best possible by internal heat buildup. performance. If you have any questions, consult your JVC – When moving the speakers, do not pull the speaker cords; dealer. otherwise, the speakers may fall over, causing damage or injury. – When holding a satellite speaker, do not grasp the Warnings, Cautions and speaker (upper) portion, but always grasp the leg (lower) portion of the satellite speaker. Others 5 Checking the supplied Accessories 5 Precautions for installation Check to be sure you have the following supplied accessories. • Do not install the speakers on an uneven surface or in a The number in parenthesis indicates the quantity of the piece place subject to vibration; otherwise, they may fall over, supplied. causing damage or injury. – Take the occurrence of earthquakes or other • Speaker cords physical shocks into consideration when selecting the installation place, and secure Approx. 5 m (3); the speakers thoroughly. For satellite speakers for front left/ right channel and center speaker • To prevent deformation or discoloration of the cabinet, do not install the speakers where they are exposed to direct sunlight or high humidity, and avoid installation near air conditioning Approx. 10 m (2); outlets. For satellite speakers for surround left/right channel • Speaker vibrations may cause howling. Place the speakers as far away from the player as • Screws (with washer) possible. M4 x 25 mm (16) • The speakers are magnetically shielded to avoid color If any of the items above are missing, contact your dealer distortions on TVs. However, if not installed properly, it may immediately. cause color distortions. So, pay attention to the following when installing the speakers. – When placing the speakers near a TV set, turn off the TV’s main power switch or unplug it before installing the Speaker and Speaker cords— speakers. to improve the sound quality Then wait at least 30 minutes before turning on the TV’s main power switch again. When connecting the speaker cords Some TVs may still be affected even though you have Make sure to match the polarity (. and ·); otherwise, followed the above. If this happens, move the speakers the sound will lose the surround effect. further away from the TV. After connecting, check that the exposed cores are fully inserted into the terminal. • Tuner reception may become noisy or hissing if a speaker is installed near the tuner. In this case, leave more distance When using other speaker cords between the tuner and the speakers or use an outdoor Observe the following; antenna for better tuner reception without interference from • Buy thick speaker cords rather than thin cords, and make the speakers. them as short as possible for connection. • Use speaker cords of the same length for both left and right speakers. 5 Precautions for Daily Use • Do not use long speaker cords; otherwise, the sound • To maintain the appearance of the speakers quality may deteriorate. Wipe with a dry, soft cloth if the cabinet or control panel should become dirty. If very dirty, apply a small amount of water or neutral detergent to the cloth and wipe clean, then wipe with a dry cloth. – 1 – Assembly English 5 Assembling the satellite speakers 2Join the stand to the speaker section. Each speaker (except the center speaker) has been divided into two parts for shipment. Before using this speaker system, assemble it first by following the procedure below. Stand • Prepare a Phillips screw driver. Speaker section 3Fix the stand to the speaker section. Speaker Stand • Be sure to tighten the screws firmly. section Before assembling— • Take care not to drop the stand while assembling; otherwise, it may cause damage to the floor or injury. • Ensure enough space for assembly and installation. • Place a large, thick cloth on the floor where you assemble the speaker, so you can protect the floor and the speaker itself. • Use the speaker only after assembly is fully and correctly done. 1Connect the speaker connecters to the stand connecters. Rear Front Front Speaker connectors Speaker section Stand Cushion (not supplied) It is recommended to place a cushion under the speaker section. • You can tighten the screws easily by placing the speaker section horizontally. Speaker section Stand Screw (4) (Supplied, M4 x 25 mm) To be continued on the next page – 2 – Assembly (continued) 4Connect the speak...