valutazioni - 3, GPA: 4.3
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
fUnctiOn bUttOn Selects the Function mode. MUte bUttOn Mutes the sound from this unit. Press again to restore the sound to the previous volume level. bASS bUttOn Optimise the sound based on your tastes. Operation range of the remote control You can use the remote control up to 23 feet (7 meters) in a straight line from the unit. You can also operate the remote at a horizontal angle of up to 30° from the remote control sensor. .Be careful not to catch your fingernail in the gap when you lift the cover. You can damage your fingernail. installing battery in the remote control 1. Open the cover of the remote control by putting your fingernail into the gap between the cover and body of the remote control. Then, lift the cover and separate it completely. 2. Install a 3V Lithium battery. Insert the battery into the battery compartment with the + side facing up. 3. Fit the remote control's cover to the remote control. Next, lower the cover so that it is flush with the body of the remote, and then press the cover into the body by pushing the edges down with your hand. 10 power on and volume control Turning the power on/off or DC 12V 2A AUX IN ONLY FOR SERVICE DC 12V 2A AUX IN ONLY FOR SERVICE MUTE VOL BASS FUNCTION MUTE VOL BASS FUNCTION 1. To turn on this unit, touch any button on the unit's front panel when the unit is in Standby mode. or, Press POWER on the remote control. 2. To turn off this unit, touch the +# button on the unit's front panel for more than 3 seconds. or, Press POWER on the remote control again. .. The standby LED is on when AC Plug is connected to the wall outlet and the Power of the unit is off. The standby LED is off when the power of the unit is on. .. The power of the unit automatically turns off if there is no input for 20 minutes. Adjusting the volume Use +, - buttons to adjust the volume. As you adjust the volume, the Input mode LED blinks. The LED remains on in case you increase the volume when it has already been set to maximum, or decrease the volume when it has already been set to minimum. MUTE VOL BASS FUNCTION MUTE VOL BASS FUNCTION DC 12V 2A AUX IN ONLY FOR SERVICE or Touch the +/– button on the right side of the front panel. or, Press VOL +/– on the remote control. .. The volume level increases or decreases when you press VOL +/–. .. You can also use the volume controls of devices connected using the Dual Dock or Bluetooth to control the volume. However, your ability to control the volume using the volume controls of devices connected using Bluetooth may be limited. connections Using rUBBer Attach the Rubber to avoid direct contact with this set when you hold Samsung Galaxy Device and Apple Device. rUbber-SUPPOrt 1. Attach the Rubber to the proper place considering the size of the device which you want to use. 2. After attach the Rubber-Support, set your device to the Dual dock. rubber-support rUbber-SKin 1. Cover the Rubber-Skin on the Dual dock. 2. After cover the Rubber-Skin on the Dual dock, set your device to the Dual dock. .Use the product after removing the Rubber-Skin attached to the product if you have the protection case for your device. rubber-skin . connEctions . You can use this product only when the thickness of the protection case is under 1.5mm when you attach the Spacer cover to your device. It is impossible to use this product when the thickness of the protection case is over 1.5mm or has special shape with round. 12 cOnnecting a DeVice tO tHe DUaL DOcK How to connect a device to the Dual Dock. 1. The DUAl DOcK is located on the front of the product. To open, push it in gently. 2. If you have a Samsung Galaxy device, connect the device to the 5 pin (smaller) connector to connect to the Dual Dock. If you have an Apple device, connect the device to the 30 pin (larger) connector on the Dual Dock. . Turn on your Samsung Galaxy device before you attach it to the Dual Dock. . This unit doesn't support the simultaneous docking of Samsung Galaxy and Apple devices. . Connect your Samsung Galaxy or Apple device to the Dual Dock before starting Docking mode. (See page 16) DC 12V 2A AUX IN ONLY FOR SERVICE DUAL DOCK DUAL DOCK 13 EnG . connEctions cOnnecting an aUDiO DeVice Using aUX in This section explains how to connect the unit to an audio device. This unit is equipped with one audio analog jack for connecting an audio device. AUX in Connect AUX IN (Audio) on the back of the unit to the earphone jack of the external device or audio device. if connected to an external device via AUX input while your Samsung galaxy device is docked or connected to a bluetooth device at the same time, the input source switches between the AUX and Samsung galaxy or bluetooth device by tapping the PAUSe button on the Samsung galaxy / bluetooth device. tap it again to switch to the other input source. . Use the Function key on the remote control to switch between connected devices, if there are multiple devices connected to the Docking station. . Before moving or installing this product, be sur...