valutazioni - 3, GPA: 4
(
)
)
|
Foto e specifiche Yamaha YST-SW1500 |
Facilità d'uso
Replace both batteries with new ones. Notes . Use only AA, R6, UM-3 batteries for replacement. . Be sure the polarities are correct. (See the illustration inside the battery compartment.) . Remove the batteries if the remote control will not be used for an extended period of time. . If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. 30°30° Remote control sensor Within approximately 6 m (20 feet) Notes . There should be no large obstacles between the remote control and the main unit. . If the remote control sensor is directly illuminated by strong lighting (especially an inverter type of fluorescent lamp etc.), it might cause the remote control not to work correctly. In this case, reposition the main unit to avoid direct lighting. E-11 CONTROLS AND THEIR FUNCTIONS SUBWOOFER SYSTEM YST-SW1500 MUSIC/MOVIE PHASE VOLUMEHIGH CUTB.A.S.S.STANDBY/ON 1 1014Hz40Hz 0 PRESET 2 3 SUBWOOFER SYSTEM YST-SW1500 MUSIC/MOVIE PHASE VOLUMEHIGH CUTB.A.S.S.STANDBY/ON 1 10140Hz40Hz 0 PRESET 2 3 578924613Front panel CONTROLS AND THEIR FUNCTIONS SUBWOOFER SYSTEM YST-SW1500 MUSIC/MOVIE PHASE VOLUMEHIGH CUTB.A.S.S.STANDBY/ON 1 1014Hz40Hz 0 PRESET 2 3 SUBWOOFER SYSTEM YST-SW1500 MUSIC/MOVIE PHASE VOLUMEHIGH CUTB.A.S.S.STANDBY/ON 1 10140Hz40Hz 0 PRESET 2 3 578924613Front panel Rear panel AC IN ON POWER OFF HIGH LOW OFF AUTO STANDBY OUTPUT INPUT REMOTE OUTPUT TO SPEAKERS INPUT 1 FROM AMPLIFIER 100Hz80Hz /MONO NORMAL INPUT 2 INPUT 3 LFE GND H.P.F.OUTPUT HIGH LOW OFF AUTO STANDBY OUTPUT INPUT REMOTE OUTPUT TO SPEAKERS INPUT 1 FROM AMPLIFIER 100Hz80Hz /MONO NORMAL INPUT 2 INPUT 3 LFE GND H.P.F.OUTPUT AC IN ON POWER OFF toyuireq0w 1 STANDBY/ON button Press this button to turn on the power. Press again to set the subwoofer in the standby mode. * This button can be used only when the POWER Remote control (A) switch is set in the ON position. Standby mode The subwoofer is still using a small amount of power in this mode. 2B.A.S.S. switch MUSIC/MOVIE button By pressing this switch to select the MOVIE mode, the bass sound in video software is faithfully reproduced. By pressing this switch to select the MUSIC mode, the bass sound in audio software is well reproduced. 3HIGH CUT control HIGH CUT UP/DOWN buttons Select the upper limit of the frequencies to be reproduced by the subwoofer. p21a43 To adjust the control on the front panel, put a coin, etc. in the groove on the control and turn it. English 4 VOLUME control VOLUME UP/DOWN buttons Adjust the volume level. Turn the control clockwise or press the UP button to increase the volume. Turn the control counterclockwise or press the DOWN button to decrease the volume. To adjust the control on the front panel, put a coin, etc. in the groove on the control and turn it. 5 Remote control sensor Receives signals from the remote control. 6 Power indicator (LED) Lights up in green while the subwoofer is turned on. Lights up in red when the subwoofer is turned into the standby mode by the automatic power-switching function. 7 MUSIC/MOVIE indicator (LED) Lights up in red when the MUSIC mode is selected, and in green when the MOVIE mode is selected. 8 PHASE indicator (LED) Lights up in red when the PHASE button (J) is set in the regular mode, and in green when it is set in the reverse mode. 9 PRESET 1/2/3 indicators (LED) Show which PRESET number (1, 2 or 3) is selected. (If the subwoofer is turned into the standby mode when one of these indicators are illuminated, no indicator will light up next time the subwoofer is turned on.) 0 AC IN