valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
Be sure to make connections firmly to avoid hum and noise. Speaker connecting cords (2) (supplied) (+) (+) (–) (–) Be sure to connect matching speaker terminals. If the connections are reversed (+ to –), the sound will lack bass. Connecting to a component other than the DVP-F11 • If your DVD player is equipped with a 2.1-channel output jacks, connect the SA-F11 in the same way as the DVP-F11. • If your DVD player is equipped with a 5.1-channel output jacks, connect the SA-F11 in the following way: – Connect the FRONT L/R of the DVD player to the DVD IN L/R of the subwoofer. – Connect the WOOFER OUT of the DVD player to the SUBWOOFER IN of the subwoofer. When you finish connecting, set the rear and center speakers setup to “NONE.” If you cannot make this setting, connect the DVD player to the AUX IN jacks. • If your DVD player is equipped with a 2-channel output jacks, connect it to the AUX IN jacks of the SA-F11. • If you connect a VCR to the SA-F11, connect it to the AUX IN jack of the SA-F11. Setting up for the DVD player Some steps are necessary for the DVD player depending on the TV or other componentes to be connected. Use the setup display to change the various settings. For details on the setup display and TV setting, see “Setting and Adjustments” in the instruction manual equipped with the DVP-F11. • To connect the player to a wide-screen TV In the setup display, set “TV TYPE” in “SCREEN SETUP” to “16:9” (default setting). • To connect the player to a conventional TV In the setup display, set “TV TYPE” in “SCREEN SETUP” to “4:3 LETTER BOX” or “4:3 PAN SCAN.” Setting up the speakers Attach the supplied foot pads to the bottom of the subwoofer and the speakers. Foot pads You can hang or install the front speakers on a wall using hooks or nuts (commercially available). Hook 60 mm Nuts Note You are responsible for the proper selection and use of mounting hardware purchased at a hardware store, and for the proper and safe mounting of the speakers. 5GB Basic Operations Operating using the remote Z Listening to the Sound 1/u INPUT MODE LEVEL +/– 1 Turn on the DVD player and insert the disc. 2 Press 1/u to turn on the subwoofer. The indicator of the 1/u button changes from red (standby mode) to green. 3 Press INPUT repeatedly until the DVD indicator lights up. 4 Press MODE repeatedly until the MASTER VOLUME indicator lights up in green, then press and hold LEVEL – to set the volume level to minimum. 5 Press · on the DVD player to start playing. Press LEVEL + or – to adjust the volume level. z You can adjust the volume selecting the tone level Press MODE repeatedly until the sound level indicator (SW VOL/BASS/TREBLE) you want to change lights up, then press LEVEL + or – to adjust the volume of the tone level you select. z You can reset the tone level to the factory setting Press and while holding the LEVEL + and –, press 1/u. z The subwoofer turns on and off automatically according to whether the audio signal is input or not (Auto Power Function) If no audio signal is input for three minutes, the subwoofer switches to standby mode and the 1/u indicator changes to red (Auto Power Off). When an audio signal is input, the subwoofer turn on automatically and the 1/u indicator changes to green (Auto Power On). Note If you press the 1/u button while listening to the subwoofer, the subwoofer switches to standby mode. Press the 1/u button again to turn it on. If the button is not pressed again within three minutes, the Auto Power On function activates the subwoofer automatically. 6GB INPUT SELECT TREBLE +/– BASS +/– WOOFER MODE MUTING TV VIDEO DVD + + – – + + + – – – The table below shows the operations you can do by using the remote. To Press Turn on/off the power 1/u Adjust the volume MASTER VOL + or – Select the component INPUT SELECT Adjust the volume of each tone LFE * S.WOOFER + or – Bass BASS + or – Treble TREBLE + or – * Low Frequency Effect Note The tone level indicator of the subwoofer changes automatically when you adjust the volume of each tone using the remote. z You can change the woofer mode according to the source Press WOOFER MODE on the remote (or press LEVEL + and – on the subwoofer at the same time). When the SW VOL indicator on the subwoofer lights up in green, the mode changes to movie mode (factory setting). When the indicator lights up in red, the mode changes to music mode. You can listen to the most suitable audio mix, depending on the source. z You can mute the sound Press MUTING on the remote. To restore the sound, press MASTER VOL + (or MUTING on the remote again). 1/u S.WOOFER +/– MASTER VOL +/– Basic Operations Basic Operations Adjusting the Sound Z You can enjoy virtual 3D sound even without rear speakers when you use the “VES (Virtual Enhanced Surround)” mode in the on-screen menu of the DVPF11. Some Sony DVD players other than the DVP-F11 also have the VES mode option. If you cannot hear the sound from the subwoofer even if you select VES mode, connect your DVD player to the AUX IN ...