valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
See the table below for the proper settings. For details on the setting procedure, refer to the manual that was provided with your amplifier. Select Micro Satellite Position if a Sony amplifier provides it. When “Hookup A” is used (Speaker setup) Adjusting the subwoofer (I) Specifications SA-VE345 1 Set MODE according to the program For the U.S. model source as follows: AUDIO POWER SPECIFICATIONS Source MODE POWER OUTPUT AND TOTAL HARMONIC DISTORTION: DVD, LD, video cassette MOVIE with 8 ohm loads, from 20 - 200 Hz; rated 120 watts per or other video source channel minimum RMS power, with no more than 0.8% MD, CD, cassette tape MUSIC total harmonic distortion from 250 milliwatts to rated output. or other audio source Tip If you use the amplifier with adjustable crossover frequency, it is recommended to select 150 Hz (or close to Black or black striped wires are minus (–) in polarity, and this figure) as the crossover frequency for your front, should be connected to the minus (–) speaker terminals. center, and surround speakers. ** “DTS” and “DTS Digital Surround” are registered trademarks of Digital Theater Systems, Inc. Positioning the speakers Maximum input power: 110 watts Location of each speaker (D) Listening to the sound (I) Each speaker should face the listening position. Better surround effect will result if all speakers are set at the First, turn down the volume on the amplifier. The same distance from the listening position. volume should be set to minimum before you begin Place the front speakers at a suitable distance to the left playing the program source. and right of the television. get the effect. Speaker system Full range, magnetically shielded Speaker units 5.5 . 11 cm (7/. 7/ 32 16 Troubleshooting in.), cone type Enclosure type Bass reflex Rated impedance 8 ohms Should you encounter a problem with your speaker Power handling capacity system, check the following list and take the indicated measures. If the problem persists, consult your nearest Sensitivity level 85 dB (1 W, 1 m) Sony dealer. Frequency range 90 Hz - 20,000 Hz Dimensions (w/h/d) Approx. 300 . 81 . There is no sound from the speaker system. 120 mm (11 7/. 4 3/. 8 4 •Make sure all the connections have been 3 1/4 in.), including front correctly made. grille Mass Approx. 1,200 g (35 lb 4 Place the subwoofer on either side of the television. • Make sure the volume on the amplifier has Place the center speaker on the top-center of the TV set. 1 Turn on the amplifier and select the oz) been turned up properly. The placement of surround speakers greatly depends on program source. • Make sure the program source selector on the the configuration of the room. The surround speakers SA-WMS345 (subwoofer) may be placed on both sides of the listening position A amplifier is set to the proper source. Speaker system Active subwoofer, or behind the listening position B. 2 Press POWER on the subwoofer. • Check if headphones are connected. If they magnetically shieldedare, disconnect them. The ON/STANDBY indicator on the Speaker unit Woofer: 20 cm (8 in.), Setting the speakers cone type To prevent speaker vibration or movement while subwoofer lights up green. There is distortion in the subwoofer sound Enclosure type Advanced SAW type listening, attach the supplied foot pads to the bottom output. Reproduction frequency range four corners of the center speaker, front speakers, and 3 Play the program source. • Check if any sound-enhancing functions have 26 Hz - 200 Hz surround speakers (E). been activated on the amplifier. If they have, Amplifier section Setting the center speaker (F) Set the center speaker firmly on top of the TV set, making sure it is completely level. Setting other speakers (G) For greater flexibility in the positioning of the speakers, use the optional WS-FV10D or WS-WV10D speaker stand (available only in certain countries). Tip The height of the front speakers should be adjusted to about the center of the TV screen (H). Power turns on and off automatically — Auto power on/off function (J) When the subwoofer is on (i.e, the ON/STANDBY indicator lights up green) and there is no signal input for a few minutes, the ON/STANDBY indicator changes to red and the subwoofer enters power saving mode. While in this mode a signal is input to the subwoofer, the subwoofer automatically turns on (auto power on/off function). To turn this feature off, slide the POWER SAVE switch on the rear panel to OFF. Note If you turn down the volume level of the amplifier too low, the auto power on/off function may activate, causing the subwoofer to enter power saving mode. turn them off. Continuous RMS power output 120 W (8 ohms, 20 Hz There is hum or noise in the speaker output. 20 kHz, 0.8% THD) •Make sure all the connections have been Inputs correctly made. •Make sure none of the audio components are LINE IN (input pin jack) positioned too close to the TV set. SPEAKER IN (input terminals) The sound has suddenly stopped. Outputs •Make sure all the conn...