valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
Selecting and recording a particular passage • During CD playback, press and hold down the SEARCH buttons . or § on the set to find your passage. • Press PLAY•PAUSE 2; to put the CD player on pause at the selected passage. . Recording will begin from this exact point in the track when you press RECORD 0. Note: If you press RECORD 0 during playback, recording starts automatically from the beginning of the current track. English 2 Insert a CD and if desired, program track numbers. 3 Press STOP•OPEN 9/ to open the cassette door. Insert a blank tape. 4 Close the cassette door. 5 Press RECORD 0 to start recording. REPEAT PROGRAM BATT.LOW TAP OFF MW FM CD LIFTTO OPEN AZ1008 CDRADIOCASSETTERECORDER CDSYNCHROSTARTRECORDING SEA RCH STOP DYNAM IC B A S S BOOST PLAY/ P A USE DBB PRO GRAM REPEAT VOLUME NEPOOTTFIL TUNING CD TRACK PLAY STOP•OPEN PAUSE SEARCH SEARCH 1 Recording from the Radio Adjust the source selector to AM or FM to select your desired waveband. 2 Tune to the desired radio station (see Radio reception). 3 Press STOP•OPEN 9/ to open the cassette door. Insert a blank tape. 4 Close the cassette door. 5 Press RECORD 0 to start recording. 6 For brief interruptions, press PAUSE ;.To resume recording, press PAUSE ; again. 7 To stop recording, press STOP•OPEN 9/ . 13 Maintenance English Precautions & General Maintenance • Place the set on a hard and flat surface so that the system does not tilt. • Do not expose the set, batteries, CDs or cassettes to humidity, rain, sand or excessive heat caused by heating equipment or direct sunlight. • Do not cover the set. Adequate ventilation with a minimum gap of 6 inches between the ventilation holes and surrounding surfaces is necessar y to prevent heat buildup. • The mechanical par ts of the set contain self-lubricating bearings and must not be oiled or lubricated. • To clean the set, use a soft, slightly dampened chamois leather. Do not use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the housing. Tape deck maintenance To ensure quality recording and playback of the tape deck, clean par ts A, B and C shown in the diagram below, after approx. 50 hours of operation, or on average once a month. Use a cotton bud slightly moistened with alcohol or a special head cleaning fluid to clean the deck. 2 Press PLAY 1 and clean the rubber pressure roller C. 3 Press PAUSE ; and clean the magnetic heads A, and also the capstan B . 4 After cleaning, press STOP•OPEN 9/. – Cleaning of the heads can also be done by playing a cleaning cassette through once. CD player and CD handling • The lens of the CD player should never be touched! • Sudden changes in the surrounding temperature can cause condensation to form and the lens of your CD player to cloud over. Playing a CD is then not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. • Use only Digital Audio CDs. • Always close the CD door to keep the CD compar tment dust-free. To clean, dust the compar tment with a soft dr y cloth. • To take a CD out of its box, press the center spindle while lifting the CD. Always pick up the CD by the edge and replace the CD back in its box after use to avoid scratching and dust. • To clean the CD, wipe in a straight line from the center towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc. • Never write on a CD or attach any stickers to it. ABC 1 Open the cassette door by pressing STOP•OPEN 9/. 14 Troubleshooting If a fault occurs, first check the points listed below before taking the set for repair. Do not open the set as there is a risk of electric shock. If you are unable to remedy a problem by following these hints, consult your dealer or service center. WARNING: Under no circumstances should you try to repair the set yourself, as this will invalidate the warranty. Problem Solution No sound – Adjust the VOLUME Power cord not securely connected – Connect AC power cord properly Batteries dead /incorrectly inserted – Inser t (fresh) batteries correctly Display does not function properly/ No reaction to operation of any of the controls – Electrostatic discharge – Switch off and unplug the set. Reconnect after a few seconds. Er indication – No CD inser ted, inser t a CD CD badly scratched or dirty – Replace/ clean CD, see Maintenance Laser lens steamed up – Wait until lens has cleared – Wait until lens has acclimatized CD-(R) is blank or the disc is not finalized – Use a finalized CD-(R) CD playback does not work – CD badly scratched/ dir ty. Replace/ clean CD (see maintenance) The CD skips tracks – CD damaged or dir ty. Replace or clean CD. – Program is active. Quit program mode Poor cassette sound quality – Dust and dir t on the heads, etc. Clean deck par ts, see maintenance. – Use of incompatible cassette types (METAL or CHROME). Only use NORMAL (IEC I) for recording Recording does not work – Cassette tab(s) may be broken. Apply a piece of adhesive ...
Questo manuale è adatto anche per i modelli :Altoparlanti - AZ1011 (3.71 mb)