valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
In such an installation, fix the speaker system to the table and check it occasionally. • • necting cables. Damaged cables may cause fire or electrical shock. • Turn off all musical instruments, and audio equipment when connecting to this unit. Use the correct connecting cables and connect as specified. • Always lower the volume control to minimum before turning on the power to this unit. A sudden blast of sound may damage your hearing. • Do not output distorted sounds for long periods of time, as this will cause the speaker to heat up, leading to a fire hazard. • Do not raise the volume of speakers to a level that makes you feel uncomfortable. Listening to loud music for long periods can damage your hearing. • If you know you will not use this unit for a long period of time, such as when going on vacation, remove the power plug from the AC outlet. Leaving it connected is a potential fire hazard. • To prevent electrical shock when cleaning the unit, remove the power plug from the AC outlet. • XLR-type connectors are wired as follows: pin 1: ground, pin 2: hot (+), and pin 3: cold (–). • This speaker is magnetically shielded. However, if a nearby monitor displays any uneven colors, place it further away from the monitor. • Using a mobile telephone near this unit may induce noise. If noise occurs, use the telephone away from the unit. Front panel/Rear panel LOW HIGH LINE 1 2 12 3 45 5 LINE 2 level control This control knob enables you to adjust the volume level of the signal input at one of the INPUT LINE 2 jacks (8) on the rear panel. Turning the knob counterclockwise lowers the volume level, and turning it clockwise raises the level. 6 8 7 ON INPUT LINE 1 (–10dB) LINE 2 (+4dB) PARALLEL OFF POWER 1 LOW control This control knob enables you to adjust the bass in the range of –3dB to +3dB based on a reference value of 100Hz. The bass range is flat with the knob set at 12 o’clock, boosted when the knob is turned clockwise, and cut when the knob is turned counter-clockwise. 2 HIGH control This control knob enables you to adjust the treble in the range of –3dB to +3dB based on a reference value of 10kHz. The treble range is flat with the knob set at 12 o’clock, boosted when the knob is turned clockwise, and cut when the knob is turned counter-clockwise. 3 Power indicator This indicator lights up green when you turn the POWER switch on the rear panel ON. 4 LINE 1 level control This control knob enables you to adjust the volume level of the signal input at the INPUT LINE 1 jack (7) on the rear panel. Turning the knob counter-clockwise lowers the volume level, and turning it clockwise raise the level. 6 POWER switch This switch turns the power to the MSP3 on and off. When you turn this switch on, the power indicator (3) lights up green. 7INPUT LINE 1 jack This input jack is used to connect an RCA pin plug. 8 INPUT LINE 2 jacks These balanced jacks are used to connect an XLR-3-31 type connector or a TRS phone plug to input line-level signals from a mixing console. CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. Specifications General specifications Type ............................................ 2-way Bass Reflex Powered Speaker Crossover Frequency ................. 4 kHz Frequency Range ....................... 65 Hz–22 kHz Maximum Output Level ........... 98 dB (1 m on Axis) Dimensions (W . H . D) ......... 144 . 236 . 167 mm Weight ........................................ 4.4 kg Magnetic shielded...................... EIAJ Speaker unit Speaker Unit LF: 10 cm cone (4., magnetic shielded) HF: 2.2 cm dome (4., magnetic shielded) Enclosure Type: Bass Reflex Amp.unit Maximum Output Power ..........20W Input Sensitivity/Impedance LINE 1: –10 dB/10 k. (RCA phono, Unbalanced) LINE 2: +4 dB/10 k. (XLR, phone Balanced) Level control LINE 1 LINE 2 Tone control HIGH LOW Power Indicator ..........................Green LED Power Requirement USA and Canada: .................AC120 V, 60 Hz Europe:..................................AC230 V, 50 Hz Others: ..................................AC240 V, 50 Hz Power Consumption ..................30 W Option ........................................BWS20-190 (Ceiling/ wall Bracket) Specifications and appearance are subject to change without notice. Dimensions 2-M5 (6) (6) 144 155 60 44 236 167 LOW HIGH LINE1 2 Unit: mm Block Diagram LINE 1 LOW LINE 2 LINE 1 LINE 2 Phone Jack HIGH TONE CONTROL P. AMP HF LF Performance graph RESPONSE (dB) +10 0 –10 –20 –30 –40 20 100 1k 10k FREQUENCY (Hz) MSP3 Mode d’emploi Nous vous remercions d’avoir porte votre choix sur l’enceinte d’ecoute Yamaha MSP3. Cette enceinte comporte un coffret bass reflex avec un haut-parleur conique a deux voies de 10 cm et un haut-parleur a dome de 2,2 cm. Ce systeme actif bi-amplifie reproduit le son avec une grande fidelite et peut servir a de nombreuses fins, allant des enregistrements a domicile a un usage professionnel serieux. Veuillez lire attentivement ce Mode d’emploi afin de...