valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
Connect the speakers as described in section 4 before continuing. Set the required horizontal angle and push the speaker back to the wall, but leave a little clearance to avoid rattles. f Go to section 4. 3.7 DS8S The speakers may be fixed to a wall or ceiling using screws in the range 5mm to 6mm diameter (No.10 to No.12). On the back of the cabinet are three wall plates. The screw head should be inserted into the round part of the aperture and slid fully along one of the slots. The slots are sprung loaded to prevent the speaker being readily knocked out of position. The screw length should be chosen to give a minimum of 25mm (1 in) engaged thread. (figure 28) Ensure, especially when fixing to drywall panels, that the screw length and wall plug security are sufficient to hold the weight of the speaker. B&W can accept no liability for any failure of wall or ceiling fixings. Use the template provided to mark the screw positions. The outside dimensions of the template correspond to the rear of the cabinet. Stick 4 of the clear self-adhesive rubber pads to the rear panel of each speaker, one close to each corner. These stop the speaker vibrating against the surface and help keep it in position. (figure 30) Adjust the protrusion of the screws such that the rubber pads are a friction slide on the surface when the wall plates are hooked over the screw heads. (figure 31) Always check and ensure that: • All the screws slide right to the ends of the slots in the wall plates. • Screw protrusion is adjusted so that the rubber pads provide enough friction to prevent the speakers sliding out of position. f Go to section 4. The ear is at its most sensitive in the 4 CONNECTIONS 4.2 800D All connections should be made with the equipment switched off. The terminals accept a variety of cable terminations to suit most applications – 4mm banana plugs, 6mm and 8mm (1/4 in and 5/16 in) spades, or bare wires up to 6mm (1/4 in) diameter. Important safety notice In certain countries, notably those in Europe, the use of 4mm banana plugs is considered a potential safety hazard, because they may be inserted into the holes of unshuttered mains supply sockets. In order to comply with European CENELEC safety regulations, the 4mm holes in the ends of the terminals are blocked by plastic pins. If you are using the products in any country where these conditions apply, you should ensure that any banana plugs cannot be used in an unsafe manner by children or other uninformed persons. Ensure each positive terminal on the speaker (coloured red and marked +) is connected to the positive output terminal of the amplifier and negative (coloured black and marked -) to negative. Incorrect connection may result in impairment of frequency response, poor imaging and loss of bass. Always screw the terminal caps down fully to prevent rattles. Model f Go to DS8S 4.3 All other models Continue All models in the range except for the DS8S may be bi-wired or bi-amplified. In 3-way systems, one set of terminals feeds the bass drivers and the other the midrange and tweeter. In 2-way systems, one set of terminals feeds the bass/ midrange driver and the other the tweeter. Separation of the signal paths to each section of the speaker can improve imaging and the resolution of low-level detail, and allows the user to optimise the cable to the frequency range of use. Bi-wiring involves the use of two separate 2-core cables from the same amplifier, one to each pair of terminals. This is the minimum we would recommend, but should you prefer to single wire, perhaps during the initial setup procedure or because you do not want to see a multitude of cables in the room, you must connect both positive and both negative speaker terminals together. midrange, so we recommend that, when single wiring, you connect the cable from the amplifier to the terminals that directly feed the midrange driver. Bi-amplification goes a stage further and involves the use of two separate power amplifier channels for each speaker. ...
Questo manuale è adatto anche per i modelli :Altoparlanti - DS8 (3.83 mb)
Altoparlanti - HTM1D (3.83 mb)
Altoparlanti - HTM2D (3.83 mb)
Altoparlanti - HTM3S (3.83 mb)