valutazioni - 1, GPA: 4
(
)
)
|
Facilità d'uso
Touch [EQ] in the Equalizer screen. 1 Touch the screen and set the Graphic Equalizer as desired. 2 Gain level (light green boxed area) Adjust the gain level by touching the each frequency bar. Touching [2], [3], [5] and [.] can also adjust the level. Use [2] and [3] to select a frequency, and [5] and [.] to set the level. EQ INIT Returns to the previous level which the gain level is adjusted. Flat Tone curve becomes flat. Bass EXT (Bass Extend Settings) When turned on, the frequency lower than 62.5 Hz is set to the same gain level as 62.5 Hz. SW Level Adjusts the subwoofer volume. This setting is not available when subwoofer is set to “None”. See Speaker setup (P.81). operation Controlling EQ curves Select EQ curve from [Natural], [Rock], [Pops], [Easy], [Top40], [Jazz], and [User] using [2] and [3]. 1 Controlling SystemQ-Ex Selectsitemstobe adjustedfortone curve setup.Ifyou turn off this setting,onlyLevel canbesetupfortone curves. Touch [ON] or [OFF] of [SystemQ-Ex]. 1 Controlling equalizer manually Touch [Tone] in the Equalizer screen. 1 Set each item as follows. 2 FREQ Adjusts the center frequency for each range. Setting values are as follows. Bass: 40Hz/50Hz/60Hz/70Hz/80Hz/100Hz/120 Hz/150Hz (Default is “100Hz.”) Middle: 500Hz/1kHz/1.5kHz/2kHz (Default is “1kHz.”) Treble: 10kHz/12.5kHz/15kHz/17.5kHz (Default is “12.5kHz.”) LEVEL Adjusts the level of each range. Each setting value is within -8dB and 8dB and default is “0dB.” Q Factor Adjust Q value for bass and middle. Setting values are as follows. Bass: 1/1.25/1.5/2 (Default is “1.”) Middle: 1/2 (Default is “1.”) Bass DC EXT Turns Bass DC EXT on or off. Default is “OFF.” If you select “ON”, the bass center frequency is extended to the low register by approximately 20%. [Flat] Tone level becomes 0 (flat). Subwoofer Level Adjusts the subwoofer volume. This setting is not available when subwoofer is set to “None”. See Speaker setup (P.81). Return to the Top page Audio Setting Up Zone Control You can selectdifferentsourcesfor both frontandrear positionsinthevehicle. Touch [Zone Control]. 1 Zone Control screen appears. Touch [Dual Zone]. 2 Set each source as follows. 3 [3] (Front Source, Rear Source) Select the audio source for each. [.], [5] (Rear VOL.) Adjusts the rear channel volume. [Single Zone] Touch to turn off the dual zone function. Continued Return to the Top page Audio Setting Up NOTE • When the rear speaker sound is switched, the audio source that is output at the AV OUTPUT Listening Position You can adjust the sound effects according terminal is also switched to the same source. toyour listening position. • When the dual zone function is set to on, the following functions are not available. • Output from the subwoofer • Subwoofer Level/Bass Boost (P.85) • Equalizer Control/Space Enhancer / Listening Position (P.85, 88, 88) • DSP Bypass Control /Speaker Setup/Car Type (DTA) Setup (P.84, 81, 83) Space Enhancer Touch [Space Enhancer]. Space Enhancer screen appears. Touch [Small], [Large], or [OFF]. Each setting value indicates the soundscape level. NOTE • This setting is not available during tuner source. Touch [Position]. 1 Position screen appears. Select listening position from [Front R] (Right front), [Front L] (Left front), [Front All] (All front), [All], and [User] using [2] and [3]. 2 NOTE • You can store present setting in memory by touching [P1], [P2], or [P3] for 2 seconds. You can also recall the setting by touching corresponding number. • The final distance is adjusted to the total of car type set up value (P.83) and position setup (both position and position DTA) value. • If you change the car type set up value (P.83), the position is set to [All]. • Only the adjusted distance of position setup (position and position DTA values) is stored in memory. Therefore, the final adjustment distance changes if you change the car type set up value (P.83). Return to the Top page Audio Setting Up Position DTA Control You can fine-adjustyour listening position. In Position screen, touch [DTA]. 1 Select the speaker you wish to adjust by touching speaker icon. 2 Set DTA as follows. [2], [3] Adjust the settings of the DTA position. Total DTA The adjusted distance (position and position DTA values), and the total of the distance adjusted by Car type (DTA) setup (P.83) and the adjustment distance for position setup are indicated. Return to the Top page Remote Controller Operation Remote Controller Thisunit canbeoperatedusingtheremotecontroller. For ,DNX6980, and DNX6480BT,the remotecontroller is supplied with the unit. For DNX6180, DNX6040EX,and DNX5180,theremotecontrolleristhe optionalaccessory(RCDV331). 2CAUTION • Put the remote controller in a place where it will not move during braking or other operations. A dangerous situation could result, if the remote controller falls down and gets wedged under the pedals while driving. • Do not leave the battery near fire or under direct sunlight. A fire, explosion or excessive heat generation may result. • Do n...
Questo manuale è adatto anche per i modelli :Navigatori GPS Car - DNX5180 (2.67 mb)
Navigatori GPS Car - DNX6040EX (2.67 mb)
Navigatori GPS Car - DNX6180 (2.67 mb)
Navigatori GPS Car - DNX6480BT (2.67 mb)