• Cannot set up the equalizer. The dual zone function Set the dual zone function to off. • Cannot set up the crossover is enabled. See Zone Control (P.101). network. “DSP Select” is set to “Bypass”. Set “DSP Select” to “Through”. See DSP select (P.97). About audio operations Problem Reason Solution Radio reception is poor. The car antenna is not extended. Pull out the antenna all the way. The antenna control Connect the wire correctly. wire is not connected. See “Connection” in the Quick Start Guide. Cannot play audio files stored in “CD Read” is set to “2”. Set “CD Read” to “1”. a disc. See Disc setup (P.27). Cannot select a folder. The random play function is enabled. Turn off the random function. Cannot perform repeat play The PBC function is Turn off the PBC function. during VCD playback. enabled. The specified disc does not play, The disc is quite dirty. Clean the disc. but another one plays instead. See Precautions on handling discs (P.4). The disc is severely Try another disc instead. scratched. The sound skips when an audio The disc is scratched Clean the disc. file is being played. or dirty. See Precautions on handling discs (P.4). The recording Record the file again or use another disc. condition is bad. Error Message Cause Solution Protect Protective circuit has been activated because a speaker cord has shorted or it has come in contact with the car chassis. Wire or insulate the speaker cord as appropriate and then push the button (P.111). Hot Error When the internal temperature of this unit rises to 60°C or more, the protection circuit is activated and you may not be able to operate the unit. Use the unit again after reducing the temperature of the unit. Mecha Error The disc player is malfunctioning. Eject the disc and try inserting it again. Contact the Kenwood dealer if this indicator continues blinking or the disc cannot be ejected. Disc Error An unplayable disc is inserted. Change the disc. See Playable Media And Files (P.112). Read Error The disc is quite dirty. Clean the disc. See Precautions on handling discs (P.4). Disc is upside down. Load the disc with the labeled side up. Region Code The disc you wanted to play has a See Region Codes In The World (P.117) or try Error region code that cannot be played another disc. with this unit. Parental Level The disc you wanted to play has a Set the parental level. Error higher level than the parental level See Parental level (P.26). you set. Error 07–67 The unit is not operating correctly Push the unit’s Reset button. If the “Error due to some reason or other. 07.67” message does not disappear, see your nearest Kenwood dealer. No Device (USB The USB device is selected as a Change the source to any source other than device) source although no USB device is USB/iPod. Connect a USB device, and change connected. the source to USB again. Disconnected The iPod/Bluetooth audio player Change the source to any source other than (iPod, Bluetooth is selected as a source although iPod/Bluetooth. Connect an iPod/Bluetooth audio player) no iPod/Bluetooth audio player is audio player, and change the source to iPod/ connected. Bluetooth again. No Media file The connected USB device contains no playable audio file. Media was played that doesn’t have data recorded that the unit can play. See Playable Media And Files (P.112) and try another USB device. 108 108108 109 Return to the Top page Return to the Top page Troubleshooting Troubleshooting Resetting The Unit If the unit or the connected unit fails to operate properly, reset the unit. 1 Press the button. The unit returns to factory settings. Error Message Cause Solution USB Device The connected USB device is rated Check the USB device. Some trouble may have Error!! a current capacity higher than the occurred to the connected USB device. allowable limit. Change the source to any source other than USB. Remove the USB device. Authorization Connection to the iPod has failed. • Remove the iPod and then reconnect it. Error • The unit does not support the iPod. See Connectable iPod/iPhone (P.114). Update your iPod The iPod’s software is an older version which the unit can not The unit may not support the connected iPod model. support. Confirm that the software for the iPod is the latest version. See Connectable iPod/iPhone (P.114). Navigation The communication error has Turn on power again after warming your car Error. Please occurred due to severely cold interior. turn on power temperature. again later. Check Application The Aha application is stopped. Start the Aha application of the your device. Please update The Aha application is an older Confirm that the Aha application is the latest your Aha version which the unit can not version. application support. NOTE • Disconnect the USB device before pressing the button. Pressing the button with the USB device connected can damage the data stored in the USB device. For how to disconnect the USB device, see How To Play Media (P.13). • When th...
