valutazioni - , GPA: ( )

Istruzioni per l'uso Directed Electronics, Modello CO652

Produttore : Directed Electronics
File Size : 1.43 mb
File Nome :

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Step 2: Place the provided template or tweeter cup against the panel and mark the two holes at the rear of the housing. Step 3: Drill the smaller holes using a 1/8" drill bit. These are the mounting screw holes. WARNING: Check for clearance of window mechanisms and electrical wires BEFORE you drill. Step 4: Drill the larger off-center hole using a 3/8" drill bit, insert a grommet and route the speaker wire from the crossover through the grommet. Step 5: After removing the surface mount tweeter assembly trim ring, route the tweeter wires through the larger hole in the housing and connect to the speaker wires from the crossover. (See Figure 4.) Step 6: Insert the excess speaker wire into the hole and position the housing so the housing will not pinch the wires after final mounting. Step 7: Attach the housing using the supplied screws of the correct length for a solid mount. Step 8: Insert the tweeter into the housing and attach the surface mount trim ring. Figure 4Figura 4Abbildung 4SurfaceMountTrim RingMountingScrewsSurface Mount HousingTweeterTweeterWirePanelWiringHarness FULL FLUSH MOUNTING Step 1:. Determine where the tweeter will be mounted. Make sure there is a flat area large enough for the tweeter and no obstructions behind the area. Step 2: Using the back half of the tweeter housing, mark with a pen the hole needed for the tweeter. Step 3: Be sure the hole is large enough for the tweeter housing, but not so large that the flange will not cover the hole.. Step 4: Cut the hole for the tweeter. When using factory locations, this step can be skipped. A hole can be cut either with a pair of metal tin snips or a 1-7/8" hole saw for hard materials. WARNING: Check for clearance of window mechanisms and electrical wires BEFORE you drill. Step 5: Install tweeter in flush mount housing. Step 6: Connect the speaker wires observing the correct polarity. Step 7: Install tweeter and housing in the hole cut for mounting, so that the trim ring is flat with the front of the surface. Step 8: Use the supplied pressure ring to secure the housing to the surface. Figure 5Figura 5Abbildung 5Flush MountTweeterAssemblyTweeterCupPressureRingTweeterWireFlush MountTrim RingWiringHarnessPanelMid/WooferWireWiringHarnessPanel Installing the Crossover Step 1: Find a location for the crossover away from any factory or after market electrical wires. It is recommended to mount the passive crossover close to the amplifier. Step 2: Mount the crossover using the supplied wire ties. Step 3: Connect the wires. Make sure the speaker wires for the midrange go to the mid/ woofer output and the tweeter to the tweeter output. Be sure to observe the correct polarity. Changing the polarity of the tweeter may be necessary for optimum sound quality. Wiring Diagram To wooferTo tweeterTo AmplifierNote: The tweeter positive is the wire marked with the stripe. Note: Le cable positif du haut-parleur d'aigus est raye. Nota. El positivo del tweeter es el cable que tiene la franja. Hinweis: Der positive Hochtonerdraht ist mit dem Streifen markiert. Nota: il filo positivo del tweeter e contrassegnato da una striscia. Nota: O cabo positivo do tweeter esta marcado com a listra. OutputInput+ _ + _ + _ Figure 6Figura 6Abbildung 6 Specifications Part Number 22130 22135 Model CO552 CO652 Nominal Impedance 4 ohm 4 ohm Power Continuous/Maximum 40 /100 w 50 /120 w Frequency Response 120 -20kHz 60 - 20kHz Sensitivity 87dB 85dB Mounting Depth 1.97"/50mm 2.36"/60mm Mounting Diameter 4.72"/120mm 5.63"/143mm Features Cone moisture and UV resistant paper cone Surround NBR (Nitrile butadiene rubber) Voice Coil 2 layer copper clad aluminum wire on a Kapton former Tweeter metalized PEI (Polyetherimide) - Ferrofluid Spider single interlaced Conex Stamped steel baskets with Eur...