Log:
valutazioni - 0, GPA: 0 ( )

Istruzioni per l'uso Philips, Modello CSP410/51

Produttore : Philips
File Size : 492.56 kb
File Nome :
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


or their respective owners. Philips reser ves the right to change products at any time without being obliged to adjust earlier supplies accordingly. 2.Your car stereo speakers Congratulations on your purchase, and welcome to Philips! To fully benefit from the suppor t that Philips offers, register your product at Introduction With the speakers, you can enjoy high power music with vivid sound. What’s in the box A Check and identify the contents of your package: a Speakers (x2) b Grille net + Frame (x2) c Speaker wire (x2) d Screw (x8) e Shrapnel (x8) 3. Installation A depth of at least 46mm is required to mount the speaker. Measure the depth of the area where you are to mount the speaker, and ensure that the speaker does not obstruct any other components of the car. Option 1: Mount on door (front or rear) B You can mount the speakers on the front/rear door of your car. a Note • Make sure that nothing obstructs around the mounting location of the door. • A hole for mounting may already be cut out of the inner panel of the door (front or rear). In this case, you need to modify the board only. • Ensure that the speaker terminals, frame or magnet do not inter fere with any inner par ts, such as the window mechanism in the door (when you open or close the window), etc. Also ensure that the speaker grille does not touch any inner fittings, such as the window crank s, door handles, arm rests etc. 1 Turn off the car ignition key. • If the power is on, the click noise generated by the connection may damage the speakers. 2 Cut out the mounting template from the packing box. 3 Paste the template on the location selected for mounting the speaker. 4 Mark the cut-off hole and the 4 bolt holes. b 5 Cut out the marked area and drill the bolt holes. c 6 Remove the grille net. d 7 Strip the speaker wires and connect them to the amplifier. e • Black wire: connect to “-“ (negative) terminal • Black (white lined): connect to “+“ (positive) terminal Note • Match the “left”, “right”, “+” and “-” terminals correctly. Revised polarity may degrade sound quality. • Two 4-ohm speaker s, wired in stereo, present a 8 ohm load to each channel of the amplifier. Most two channel amplifier s work well in this configuration. However, if two 4-ohm speakers, wired in parallel to a bridged two -channel amplifier, present a 2-ohm mono load to the amplifier. Most 2-channel amplifiers do not suppor t 2-ohm mono operation! Amplifier damage may result! 8 Mount on the speaker as shown below. f 9 Press and inser t the edges of the grille net. g Tip • The speaker grille can be mounted without the grille net, if you like. Option 2: Mount on rear tray C You can also mount the speakers into the surface of the rear tray. Follow the steps in section “Option 1: Mount in door” to mount the speakers into the rear tray: 4. Product information Note • Product information is subject to change without prior notice. Model CSP410 CSP510 Speaker type 10cm 2-way coaxial speaker 13cm, ...

Questo manuale è adatto anche per i modelli :
Altoparlanti per auto e Subwoofer - CSP510/51 (492.56 kb)
Altoparlanti per auto e Subwoofer - CSP610/51 (492.56 kb)
Altoparlanti per auto e Subwoofer - CSP6910/51 (492.57 kb)
Altoparlanti per auto e Subwoofer - CSP410/00 (492.56 kb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie