Log:
valutazioni - 3, GPA: 4.3 ( )

Istruzioni per l'uso Britax, Modello BOULEVARD 70

Produttore : Britax
File Size : 5.4 mb
File Nome : 80.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


33IMPORTANT: • The harness buckle strap should lie toward the back of the child seat during installation. • The buckle should be in the inner slot for rear-facing installation. 34 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Remove the body pillow, unbuckle the harness, and remove the belly pad. 3 Pull the head restraint cover up, then pull the seat cover forward while pulling the buckle through to access the rear-facing belt path. IMPORTANT: Ensure buckle is in inner slot and lying away from the belt path. 4 Open the blue lock-off closest to where the vehicle belt will be buckled. a Open the locking tab b Open the clamp 5 Route the vehicle belt through the rear-facing belt slots, then buckle. Ensure the vehicle belt is not twisted. 6 Push down into the middle of the child seating area with moderate force while removing all slack from the bottom (lap) part of the vehicle belt and close the lock-off. a Close the clamp over the vehicle belt b Slide your palm or thumb along the locking tab until a click is heard (see page 19) 7 Push the child seat down while pulling the top (shoulder) part of the belt between the belt slots to remove any remaining slack through the lock-off. 1b 1a LOCKING TAB CLAMP 4a 4b 5 7 Rear-Facing Installation Rear-Facing Installation Rear-Facing Installation 8 Rear-facing installations can be improved by the use of the Versa-Tether (see pages 24 – 27). 9 Pull the buckle up through its appropriate slot in the cover. 10 Replace the cover and the belly pad. 35 Checklist9Check that the vehicle belt is securely fastened. 9Check that the child seat cannot be moved front to back or side to side more than 1 in. (2.5 cm) at the belt path. If the child seat is not secure, repeat installation or use a different seating location. 9Check that the back angle of the child seat is 30. – 45. from vertical (not to exceed 45.) when the car is parked on a level surface. * If necessary, the proper recline angle can be achieved by placing a rolled towel or pool noodle in the vehicle seat bight. Check buckleconnectionCheck that thechild seat isreclined to position 3Check that there isLESS than 1 in. (2.5 cm) of movement (front to back orside to side) at the belt path Rear-Facing Installation Rear-Facing Installation Lap Belt Installation Before You Begin: • Check that your vehicle belt is compatible for use with child seats. See pages 8 – 13 for more information. • This child seat must be reclined to position 3 and placed rear-facing on the vehicle seat. * When properly installed in the rear-facing position, the back angle of the child seat should be at least 30. for children and up to 45. from vertical for infants unable to maintain head and neck control (not to exceed 45.) when the car is parked on a level surface. Use the blue line as a guide to achieve the proper recline angle for rear-facing installations. The blue line will be parallel to the ground when the child seat angle is at the center of the angle range (30 – 45.). If necessary, the proper recline angle can be achieved by placing a rolled towel or pool noodle in the vehicle seat bight. • Britax recommends that the Versa-Tether is used at all times. Using the tether will improve the stability of the child seat and reduce the risk of injury. Check your vehicle owner’s manual for tether anchor locations. See page 25 for possible rear-facing tether configurations. 36 Rear-Facing Installation Rear-Facing Installation Install with lap belt as shown above. 37IMPORTANT: • The harness buckle strap should lie toward the back of the child seat during installation. • DO NOT use lock-offs for lap belt installations. • The buckle should be in the inner slot for rear-facing installation. 38 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Remove the body pillow, unbuckle the harness, and remove the belly pad. 3 Pull the head restraint cover up, then pull the seat cover forward while pulling the buckle through to access the rear-facing belt path. 4 Route the vehicle seat belt through the rear-facing belt slots, then buckle. Ensure the vehicle belt is not twisted. 5 Push the child seat down while pulling the vehicle belt to remove all slack (see pages 10 – 11). 6 Rear-facing installations can be improved by the use of the Versa- Tether (see pages 24 – 27). 7 Pull the buckle up through its appropriate slot in the cover. 8 Replace the cover and belly pad. 1b 1a 3 4 5 Rear-Facing Installation 39 Checklist9Check that the vehicle belt is securely fastened. 9Check that the child seat cannot be moved front to back or side to side more than 1 in. (2.5 cm) at the belt path. If the child seat is not secure, repeat installation or use a different seating location. 9Check that the back angle of the child seat is 30. – 45. from vertical (not to exceed 45.) when the car is parked on a level surface. * If necessary, the proper recline angle can be achieved by placing a rolled towel or pool noodl...


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie