|
Facilità d'uso
• A) Radio Housing • B) Radio Housing Brackets KIT COMPONENTS A B C D APPLICATIONS Toyota Tacoma 2005-2011 • C) Radio Housing Trim Panel • D) ISO Brackets • E) ISO Trim Plate • F) (4) #6 x 3/8” Phillips Pan Head Screws • G) (4) #8 X 3/8” Phillips Truss Head Screws • H) Double DIN Trim Plate • I) Clock/Hazard Switch Bracket E F G H 99-8214TB 99-8214TG TOOLS REQUIRED: I WIRING AND ANTENNA CONNECTIONS (Sold Separately) Harness: • 70-1761 - Toyota harness 1987-up • TYTO-01 - Toyota amp interface harness 2003-up Antenna Adapter: • Not required 99-8214 99-8214 TABLE OF CONTENTS DashDisassembly ................................... 1 KitPreparation ..................................... 2 KitAssembly ...................................3,4,5,6 FinalAssembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... 7 KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto or call 800-354-6782 for more information and take steps toward a better tomorrow. 99-8214DASHDISASSEMBLY99-8214DASHDISASSEMBLY TOYOTA TACOMA 2005-2011 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove A/C control panel. (Figure A) 3 Remove (4) 10 MM bolts securing radio. (Figure B) 4 Unclip and remove entire panel including hazard switch and clock. (Figure C) SCAN TEXT PWR VOL A Removetheleftandrightradiobracketsfromtheradiochassis. (FigureD) 5Unclipandremovetheclock/hazardswitchassemblyfromthefactoryradiohousingtrimpanel.(FigureE) 6SCAN TEXT PWR VOL BCDContinuetoKitPreparation. E 1 99-8214KITPREPARATION99-8214KITPREPARATION TACOMA 2005-2011 (SKIP KIT PREPARATION WHEN INSTALLING DDIN RADIO) A Attach the clock/hazard switch bracket to the radio housing using the (4) #6 x 3/8” Phillips pan head screws. 1 WARNING: DO NOT OVERTIGHTEN SCREWS. 2 Clip the clock/hazard switch assembly into the 99-8214 Radio Housing Trim Panel. (Figure A,B) Continue to Kit Assembly. H M PASSENGER PASSENGER INSERT CLOCK/HAZARD SWITCH ASSEMBLY FROM REAR OF 99-8214 RADIO HOUSING TRIM PANEL B H M PASSENGER PASSENGER 2 99-8214KITASSEMBLY99-8214KITASSEMBLY TOYOTA TACOMA 2005-2011 DIN HEAD UNIT PROVISION A 1 Attach the corresponding radio housing bracket to the radio housing using the included (4) #8 x 3/8” 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure B) 3 Slide the aftermarket head unit into the cage and secure. (Figure C) B 4 Secure the Radio Housing into the dash using the factory hardware. Continue to Final Assembly. C 3 99-8214KITASSEMBLY99-8214KITASSEMBLY TOYOTA TACOMA 2005-2011 ISO DIN HEAD UNIT PROVISION A 1 Attach the corresponding radio housing bracket to the radio housing using the included (4) #8 x 3/8” Phillips truss head screws.(Figure A) 2 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure B) 3 Slide the head unit into the radio opening until the side clips engage. (Figure C) B 4 Snap the ISO Trim Plate into the Radio Housing. (Figure C) 5 Secure the radio housing into the dash using the factory hardware. Continue to Final Assembly. C 4 99-8214KITASSEMBLY99-8214KITASSEMBLY DOUBLE DIN HEAD UNIT PROVISION A 1 Slide the aftermarket radio unit into the factory brackets and secure the unit to the brackets using the screws supplied with the head unit. (Figure A) 2 Secure the aftermarket radio unit and factory bracket assembly into the sub dash. (Figure B) 3 Place the Double DIN trim plate into the back of the radio housing, then attach the clock/hazard switch brack- et assembly using th...
Questo manuale è adatto anche per i modelli :Unità - 99-8214TG (1.07 mb)