valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
iPod does not play and no sound is output. • The iPod has not been recognized. -Turn the ignition key off, and then set to ON again. -To reset the iPod, refer to the Owner’s Manual of the iPod. If the above-mentioned solution does not solve the problem, consult your nearest Alpine dealer. Indication for CD Player • No CD is inserted. -Insert a CD. • Although a disc is inserted, “NO DISC” is displayed and the unit does not start to play or eject the disc. -Remove the disc by following these steps: Press the button again for at least 2 seconds. If the disc still does not eject, consult your Alpine dealer. • Mechanism error. 1) Press the button and eject the CD. If not ejecting, consult your Alpine dealer. 2) When the error indication remains after ejecting, press the button again. If the error indication still does not turn off after pressing the button for a few times, consult your Alpine dealer. • A copy-protected WMA file was played back. -You can only play back non-copy-protected files. • A sampling rate/bit rate not supported by the unit is used. - Use a sampling rate/bit rate that is supported by the unit. 23-EN Indication for Flash memory Indication for iPod Mode • Abnormal current is run to the USB port (an error message may be displayed if the USB device that is not compatible with the unit is connected). Flash memory malfunction. -Connect another flash memory. • A USB device that is not supported by the unit is connected. -Connect a USB device that is supported by the unit. NO DEVICE • Flash memory is not connected or not recognized. - Make sure the flash memory device is correctly connected and the cable is not excessively bent. • The iPod/iPhone is not connected or not recognized. - Make sure the iPod/iPhone is correctly connected (refer to “Connections” on page 28). Make sure the cable is not bent excessively. • There are no songs in the iPod/iPhone. - Download songs to the iPod/iPhone and connect to this unit. • Communication error. -Reset the iPod. -Check the display by reconnecting between the iPod/ iPhone and this unit, using the iPod/iPhone cable. • Caused by the iPod/iPhone Software Version not being compatible with this unit. -Update the iPod/iPhone Software Version to be compatible with this unit. • The iPod/iPhone is not verified. -Reset the iPod. -Try another iPod/iPhone, if available. • Power surge error. -Excessive voltage/current is supplied to the iPod/ iPhone. -Try another iPod/iPhone, if available. -Turn the ignition key off, and then set to ON again. • No song (file) is stored in the flash memory. - Connect the flash memory device after storing songs (files). • A sampling rate/bit rate not supported by the unit is used. - Use a sampling rate/bit rate that is supported by the unit. • A copy-protected WMA file was played back. -You can only play back non-copy-protected files. NO SUPPORT • Text information that is not recognizable by the unit has been input. -Use a flash memory device with input text information that is supported by the unit. 24-EN GENERAL Specifications FM TUNER SECTION Tuning Range 87.7-107.9 MHz Mono Usable Sensitivity 9.3 dBf (0.8 .V/75 ohms) 50 dB Quieting Sensitivity 13.5 dBf (1.3 .V/ 75 ohms) Alternate Channel Selectivity 80 dB Signal-to-Noise Ratio 65 dB Stereo Separation 35 dB Capture Ratio 2.0 dB AM TUNER SECTION Tuning Range 530-1,710 kHz Sensitivity (IEC Standard) 22.5 .V/27 dB CD PLAYER SECTION Frequency Response 5-20,000 Hz (±1 dB) Wow & Flutter (% WRMS) Below measurable limits Total Harmonic Distortion 0.008% (at 1 kHz) Dynamic Range 95 dB (at 1 kHz) Signal-to-Noise Ratio 105 dB Channel Separation 85 dB (at 1 kHz) PICKUP Wave length 795 nm Laser power CLASS I USB SECTION USB requirements USB 1.1/2.0 Max. Power Consumption 500 mA USB Class Mass Storage File System FAT 12/16/32 MP3 Decoding MPEG-1/2 AUDIO Layer-3 WMA Decoding Windows Media™ Audio AAC Decoding AAC-LC format “.m4a” file Number of Channels 2-Channel (Stereo) Frequency Response* 5-20,000 Hz (±1 dB) Total Harmonic Distortion 0.008% (at 1 kHz) Dynamic Range 95 dB (at 1 kHz) Signal-to-Noise Ratio 105 dB Channel Separation 85 dB (at 1 kHz) *Frequency response may differ depending on the encoder software/bit rate. Power Requirement 14.4 V DC (11-16 V allowable) Power Output 18 W RMS . 4* * Primary amplifier ratings per CEA-2006 Standard • Power output: measured at 4 Ohms and 1% THD+N • S/N: 80 dBA (reference: 1 W into 4 Ohms) Maximum Pre-Output Voltage 2 V/10 k ohms Bass ±14 dB at 100 Hz Treble ±14 dB at 10 kHz Weight 1.5 kg (3 lbs. 4 oz) CHASSIS SIZE Width 178 mm (7") Height 50 mm (2") Depth 161 mm (6-3/8") NOSEPIECE SIZE Width 170 mm (6-3/4") Height 46 mm (1-13/16") Depth 25 mm (1") • Due to continuous product improvement, specifications and design are subject to change without notice. 25-EN Installation and Connections Before installing or connecting the unit, please read the following and pages 3 to 5 of this manual thoroughly for proper use. Warning MAKE THE CORRECT CONNECTIONS. Failure to ...