valutazioni - 5, GPA: 4.6 ( )

Produttore : Panasonic File Size : 5.57 mb File Nome : CQDF583U.PDF Lingua di insegnamento:

. The changer has become disconnected from the main unit in the changer mode. .Verify that correct connections have been made. CQ-DFX683U CQ-DF583U Notes on CD-Rs/RWs Notes on CD/CD Media (CD-ROM, CD-R, CD-RW) 31 H S I L G N E Installation E N G L I S H 32 WARNING This installation information for experienced installers not intended for non-technical individuals. It does not contain warnings or cautions of potential dangers involved in attempting to install this product. . Installation Hardware No. Item Diagram Q’ty 1 Mounting collar 1 2 Hex. nut (5 mm · ) 1 3 Rear support strap 1 4 Tapping screw (5 mm ·a16 mm) 1 5 Mounting bolt (5 mm · ) 1 6 Power connector 1 7 Removable face plate case 1 8 Trim plate 1 9 Lock cancel plate 2 . Overview This product should be installed by a professional. However, if you plan to install this product yourself, your first step is to decide where to install it. The instructions in these pages will guide you through the remaining steps: (Please refer to the “WARNING” statement above.) . Identify and label the car wires. . Connect the car wires to the wires of the power connector. Any attempt to install this product motor car by anyone other than installer could cause damage electrical system and could result in personal injury or death. . Install the unit in the dashboard. . Check the operation of the unit. If you encounter problems, please consult your nearest professional installer. Caution: . This unit operates with a 12 V DC negative ground auto battery system only. Do not at-tempt to use it in any other system. Doing so could cause serious damage. Before you begin installation, look for the items which are packed with your unit. . Warranty Card…Fill this out promptly. . Panasonic Servicenter List for Service Directory …Keep for future reference in case the product needs servicing. . Installation Hardware…Needed for in-dash installation. . Required Tools You’ll need a screwdriver, a 1.5 V AA battery, and the following: 12 V DC Electrical Side-cut Test bulb tape pliers . Dashboard Specifications Thickness Min. 3. 16z (4.75 mm) 75. Max. 7. 32z (5.56 mm) 23. 32z (53 mm) 32z (182 mm) . Identify All Leads The first step in installation is wires you’ll use when hooking up As you identify each wire, we suggest it using masking tape and a permanent marker. will help avoid confusion when making connections later. Note: . Do not connect the power connector to the stereo unit until you have made all connections. If there are no plastic caps on the stereo hooking wires, insulate all exposed leads with electrical tape until you are ready to use them. Identify the leads in the following order. Power Lead If your car has a radio or is pre-wired for one: Cut the connector wires one at a time from the plug (leaving the leads as long as possible) so that you can work with individual leads. Turn the ignition on to the accessory position, and ground one lead of the test bulb to the chassis. Touch the other lead of the test bulb to each of the exposed wires from the cut radio connector plug. Touch one wire at a time until you find the outlet that causes the test bulb to light. Now turn the ignition off and then on. If the bulb also turns off and on, that outlet is the car power lead. If your car is not wired for an audio unit: Go to the fuse block and find the fuse port for radio (RADIO), accessory (ACC), or ignition (IGN) . Battery Lead If your stereo unit has a yellow lead, you will need to locate the car’s battery lead. Otherwise you may ignore this procedure. (The yellow battery lead provides continuous power to maintain a clock, memory storage, or other function.) If your car has a radio or is pre-wired for one: With the ignition and headlights off, identify the car battery lead by grounding one lead of the test bulb to the chassis and checking the remaining exposed wires from the cut radio connector plug. If your car is not wired for Go to the fuse block and find battery, usually marked BAT. Speakers Identify the car speaker leads. There are for each speaker which are usually color A handy way to identify the speaker leads and speaker they are connected with is to test the leads using a 1.5 V AA battery as follows. Hold one lead against one pole of the battery and stroke the other lead across the other pole. You will hear a scraping sound in one of the speakers if you are holding a speaker lead. If not, keep testing different lead combinations until you have located all the speaker leads. When you label them, include the speaker location for each. Antenna Motor If your car is equipped with an automatic power antenna, identify the car motor antenna lead by connecting one bulb tester lead to the car battery lead and touching the remaining exposed wires from the cut radio connector plug one at a time. You will hear the antenna motor activate when you touch the correct wire. Antenna The antenna lead is a thick, black wire with a metal plug at the end. . Connect All Leads Now that you have iden...

Scarica la tua

Per scaricare, digitare 2 cifre :