valutazioni - 3, GPA: 4.3 ( )

Produttore : Panasonic File Size : 1.8 mb File Nome : CQDP940EUC.PDF Lingua di insegnamento:

When PWR is switched on, the volume level is low. After that, the volume level gradually returns to its previous level prior to switching off the unit. CQ-DP940/930EUC 7 Power and Sound Controls continued ran . —3 .........—■ " 3 i.............. » 11 ........a * ■■ /’ illL «/ .......... .B- Tone Enhancement (omyforcq-dp93oeuc) Press LOUD ( © ) to enhance bass and treble tones when listening at low or medium volume. Press LOUD ( © ) again to deactivate. LOUD Changing Audio Modes Press SEL to switch the audio mode in the following order. VOLUME * FADER BASS TREBLE « BALANCE Bass and Treble • Press SEL to select the BASS (TREBLE) mode. Press “VOL/V1 or “VOLv” to increase or decrease the bass/treble response. -12 to 12 -12 to 12 • Press “VOL^" or “VOL^” for more than a half second to change numeric levels on the display rapidly. Balance • Press SEL to select the BALANCE mode. Press “VOL^” or “VOLV’ to shift the sound volume to right or left speakers. UHL W ¡5 IWVu UN ! or L 1 to 15 Balance Center • Press “VOL^” or “VOL'""” for more than a half second to change numeric levels on the display rapidly. Fader • Press SEL to select the FADER mode. Press “VOL/v” or “VOLv” to shift the sound volume to the front or rear speakers. FR3 F 15 FR2 ONT I I I or R 1 to 15 Balance Center • Press “VOL/v" or “VOL''” for more than a half second to change numeric levels on the display rapidly. Note: When a control mode (BAS/TRE/BAL/FAD) is selected but no operation is made within 5 seconds(2 seconds at volume mode), the display will return to the normal operation (Radio, CD, etc) mode. In such a case, press SEL again to select the control mode. 8 CQ-DP940/930EUC Selecting Auxiliary Source • Press AUX to select AUX Input mode. (Only for CQ-DP940EUC) PM V/ f iu/i Connect the auxiliary equipment (an optional DCC player deck or any other appropriate equipment) to the AUX Jack. Press AUX or MODE again while the AUX mode is operated, the mode will return to the previous mode. Or insert a CD and the mode will change to CD mode. Note: The AUX mode enables setting of VOL,BAS,and FAD,independently of other modes. (Only for CQ-DP940EUC) on Caution: In order to insert the plug into the “AUX” Jack properly, make sure to use the correct size of the stereo plug shown on the left. A-MIN 1/2" LONG (12mm) B-MAX 2/5" DIA. (10mm) C-MIN 1/8” DIA. (3.5mm) Radio Basics To change Tuner Mode Tuner mode is selected if the MODE button is pressed while in CD Player. You can select FM or AM directly. Selecting a Band • Press BAND to select the bands in the following order. • Press FM to select the bands in the following order. FM1- •AM J FM1 FM2 FM3 • Press AM to select the bands. “STEREO” indicator lights if the station is broadcasting in stereo. Manual Tuning Press TUNE^” or “^TUNE” to move to a higher or lower frequency. Seek Tuning Press and hold “TUNE^” or “^TUNE” for more than a half second, then release. The radio automatically stops on the next station. MONO/LOCAL Selection • Much interference is reduced during a weak FM stereo broadcasts when MONO is ON. (Only for FM mode) • Searching stops automatically at a strong wave station only when LOG is ON Press MONO to switch on or off the MONO mode as follows. MONO OFF —►MONO ON Press LOC to switch on or off the LOC mode as follows. LOC OFF + > LOC ON iMONOl LOCAL 10 CQ-DP940/930EUC Press and Hold Preset Station Setting Up to 24 stations can be preset in the station memory as follows; FM1 FM2 FM3 AM 6 stations 6 stations 6 stations 6 stations Manual Station Preset © Press BAND to select adesired band. You can select FM or AM directly. ©Use manual or seek tuning to find a station that you want to program into memory. (D Press and hold one of the station selector buttons 1 through 6 until the display blinks. Repeat the process to set other stations for the FM1 to AM bands. Note: You can change the memory setting by repeating the above procedure. Tuning in a Preset Station Press any of the buttons 1 through 6 to tune in the station preset by the above steps © to CD. Auto Station Preset Select a band and press and hold APM (AUTO PRESET) for more than 2 seconds. (Only for CQ-DP940EUC) Select a band and press APM. (Only for CQ-DP930EUC) • The 6 strongest available stations will be automatically set in memory preset buttons 1 through 6. • Once set, the preset stations are sequentially scanned for 5 seconds. • Press the appropriate preset button for the station you want to hear. Caution: For safety reasons, do not attempt to program while driving. CQ-DP940/930EUC 1 Compact Disc Player Basics Mode Selection While the disc is inserted, press MODE to switch the operation mode in the following order. Tuner -► CD Player You can select CD play (pres...

Scarica la tua

Per scaricare, digitare 2 cifre :