valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
General Power Signal sensor u d FMAMSRCCLKAUDDISPAUTOMTL/M.RDMD.SCNREPB.S/RDMSCANBNRLOUDNAME.SAMEATTNFDISCDABEJECTDISCOFFMENUPROG/PTY ATT / LOUD #1 ~ 6 AUD FM AM/NF 4 CLK SRC /OFF You can help prevent . faceplate so that the unit, and shutting off Power ON/OFF: When you turn your vehicle's also turn on, with the faceplate reversing panel. When you turn your vehicle's ignition reverse to hide the control panel after a you have set in the "Time setting for removing the menu. The unit's power will turn off. Alternatively, you can remove the faceplate during For details, refer to the "Removing the faceplate" ATT indicator . indicator LOUD indicator NOTE • When the moving faceplate is hit by an object, it will stop return to its original state. Remove the object and repeat action. • The status of the security code Function (P.34) is display whenever the power is switched on. "CODE ON" (Security code has been registered) "CODE OFF" (Security code has not been registered) 2CAUTION Using the Unit in Vehicles with Covered Consoles • Make sure the console is uncovered while the faceplate is reversed. • Do not exert any excess force on the movable parts of the unit, including the faceplate, as it can cause failure in the unit’s mechanism. — 5— General Switching Modes Volume English Switching Modes: Each time you press the switches as follows: Ў Tuner mode Ў Tape mode Ў External disc control mode 1 Ў External disc control mode 2/AUX mode Ў Standby mode Selecting standby mode: Press the SRC button repeatedly and switch to "ALL OFF" When "ALL OFF" is displayed, the standby mode is activated. The standby mode turns all functions off while leaving the power to the unit on. Use this mode when you want to have the display illuminated but don't want to listen to anything. Increasing Volume: Press the u button to turn up the volume. Decreasing Volume: Press the d button to turn down the volume. Attenuator This function allows you to turn down the Turning Attenuator On/Off: Press the ATT button to switch the attenuator on When the attenuator is on, the ATT indicator blinks. When the attenuator is off, the volume returns to the level. NOTE Turning the volume up, or turning it all the way down deactivates the attenuator function. NOTE • The mode switches to the next mode from any mode which cannot be used. • The external disc control mode will differ depending on the unit that is connected. • The AUX mode is available only when the changer / AUX switching adapter (KCA-S210A or CA-C1AX) or CD changer (KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connected to this unit. During the AUX mode, "AUX" / AUX-name will show in the display. When the CA-C1AX is being used, the AUX Mode will replace the External Disc Control Mode. NOTE Presetting AUX-name In the AUX mode, press the NAME.S button for at least two seconds. "NAME SET" is display and AUX-name mode is entered. Input the characters, referring to the section on "Presetting Disc Names (DNPS)" (page26). Loudness This function amplifies low and high tones when the volume is turned down. The LOUD indicator lights up when the loudness function is on. Turning Loudness On/Off: Press the LOUD button for at least one second to switch the loudness on and off. NOTE The loudness function does not affect non-fading pre-out. — 6— Audio Control Adjust various parameters 1 Press the AUD button to 2 Selecting mode Press either the FM or AM button. Each time the button is pressed, change. Please refer to the following for the adjustment modes. NOTE Source tone memory Each source ( tape, CD, FM, AM and disc changer memory in which to store the bass, treble and N-The settings made for a particular source are recalled automatically whenever you use that source ( for example, mode uses the tone settings made for FM, AM for AM, 3 Adjust each mode Press the 4/ . button. Please refer to the following for the adjusting values. 4 Press the AUD button to end the control mode. Function of the "Bass F" : Adjust the center Setting values: 60 / 70 factor is set to 1.00, 1.25 quality factor is set to 2.00) NOTE This mode is available only when on. (page36) "Bass" : Adjust the bass level. Setting values: - 8 – + 8 Function of the KRC-X858 "Bass Q" : Adjust the Bass quality factor. Setting values: 1.00 / 1.25 / 1.50 / 2.00 "Kex"/"ec4"/"dB" : Recalling the kenwood preset sound setting Press the preset buttons (#1-6). Settings: #1;Flat, #2;Rock, #3;Pops/Top40, #4;Jazz, #5;Easy, #6;Scan of #1-5 NOTE • This mode is available only when the Sound coordinate system is on. (page36) • You can call the following settings with this function; bass center frequency, bass level, bass quality factor, bass extension, treble center frequency, and treble level setting. Their setting values are different depending on the setting of the mobile preset plan mode. NOTE This mode is available only when the Sound coordinate system is on. (page36) Function of the KRC-X858 "Bass EXT" : Switch the Bass Extend mode on/off. Setting values: ON ...
Questo manuale è adatto anche per i modelli :Unità - KRC-X858 (691.31 kb)