valutazioni - 2, GPA: 4.5 ( )

Produttore : Kenwood File Size : 2.04 mb File Nome : Lingua di insegnamento:

Power control/ Motor antenna control wire (Blue/White) TEL mute wire (Brown) Connect either to the the vehicle. A–7 Pin (Red) A–4 Pin (Yellow) Connector A Connector B See page 35 Fuse (10A) Connector Function Guide Antenna Cord (ISO) Connect to the terminal that is grounded when either the telephone rings or during conversation. To connect the KENWOOD navigation system, consult your navigation manual. power control terminal when using the optional power amplifier, or to the antenna control terminal Pin Numbers for ISO Connectors Cable Color Functions External Power Connector A–4 A–5 A–7 A–8 Yellow Blue/White Red Black Battery Power Control Ignition (ACC) Earth (Ground) Connection Speaker Connector B–1 B–2 B–3 B–4 B–5 B–6 B–7 B–8 Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black Rear Right (+) Rear Right (–) Front Right (+) Front Right (–) Front Left (+) Front Left (–) Rear Left (+) Rear Left (–) Connecting Wires to Terminals (KRC-666R) Connecting Wires to Terminals (KRC-666R) Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated. Please be sure to reconnect the cable as shown 2 below to install this unit to the Volkswagen vehicles etc. 1 (Default setting) The A-7 pin (red) of the vehicle's ISO connector is linked with the ignition, and the A-4 pin (yellow) is connected to the constant power supply. Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) 2 The A-7 pin (red) of the vehicle's ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition. Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) 3 The A-4 pin (yellow) of the vehicle's connected to anything, while the constant power supply (yellow) pins are connected Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable A–4 Pin (Yellow) When the connection is made as in 3 above, the unit's power will not be linked to the ignition key. For that reason, always make sure to turn off the unit's power when the ignition is turned off. To link the unit's power to the ignition, connect the ignition cable (ACC...red) to a power source that can be turned on and off with the ignition key. ¦ Installation Firewall or metal support Metal mounting strap (commercially available) Self-tapping screw (commercially available) Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Make sure that the unit unstable, it may malfunction — 35 — Installation Installation ¦ Installing in Japanese-Made Cars 3 Tighten the screw (o2.6 . 12 mm) (Accessory 5) in the hole shown on the diagram. 1 Refer to the section (page 37) and then remove the hard rubber frame. 2 Align the holes in the unit (two locations on each side) with the vehicle mounting bracket and secure the unit with the accessory screws. N T N 8 mm MAX. o5mm o5mm 8mm MAX. 34 T/N T 4 Tighten the screw (o2 . 4 mm) (Accessory 6) in the hole shown on the diagram. T: Toyota cars N: Nissan cars Accessory3...for Nissan car Accessory4 ...for Toyota car • During installation, do not use any screws except for those provided. The use of different screws might result in damage to the main unit. Accessory6 • Damage may occur if a screwdriver or similar tool is used with excessive force during the installations. 5 Tighten the screws (o2 . 6 mm) (Accessory 7) in the holes shown on the diagram. Accessory5 ¦ Screwing the Faceplate on the Unit If you want to fasten the faceplate does not fall off. 1 Refer to the section and then remove the hard rubber frame. 2 Remove the screw (M4 . 8) on the back panel. 3 Insert the two removal tools deeply into the slots on each side, as shown. Screw (M4X8) (commercially available) Accessory2 Removal tool 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. — 37 — 37— 37 — —— English English What might seem to be a malfunction in your unit may just be ...

Scarica la tua

Per scaricare, digitare 2 cifre :