|
Facilità d'uso
The use of different screws might result in damage y available) the main unit. • Damage may occur if a screwdriver or similar tool is used with excessive force during the installations. NOTE Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). — 21— Installation Removing Removing English 1 Engage the catch locks on the lower level. Lower the frame and pull Catch Lock Accessory3 Removal tool 2 When the lower level is removed, remove the upper locations. The frame can be removed from the top side in the same manner. Accessory4 Lower the removal tool toward the bottom, and pull out the unit halfway whilst pressing towards the inside. 4 Pull the unit all the way out with your hands, being careful not to drop it. 5 Be careful to avoid injury from the catch pins on the removal tool. Catch facing up Refer to the section “ Removing the hard ” and then remove the Remove the Hex-head on the back panel. Insert the two removal tools deeply as shown. 3 2 1 Accessory3 Removal tool NOTE 2CAUTION — 22— Screwing If you want to fasten does not fall off, screw o4 . 16 mm) in the hole shown below. Accessory7 2CAUTION Never insert the taptite screw ( o4 . 16 mm) in any other screw hole than the one specified. If you screw it in another hole, contact and may cause damage to the mechanical parts inside the unit. — 23— Troubleshooting What might Before calling PROBLEM POSSIBLE CAUSE SOLUTION The power does not turn on. The fuse has blown. After checking for short circuits fuse with one with the same No sound can be heard, or the Attenuator is turned on. Turn off Attenuator. volume is low. The fader or balance settings are set all Reset the fader or balance settings. side. The input/output wires or wiring harness are Reconnect the input/output wires or the wiring incorrectly. correctly. See the section on "Connecting Wires Terminals". Nothing happens when the The computer chip in the unit is not functioning normally. Press the reset button on the unit (see p. 5). buttons are pressed. The sound quality is poor or One of the speaker wires is being pinched by a screw in Check the speaker wiring. distorted. the car. The speakers are not wired correctly. Reconnect the speaker wires so that each output terminal is connected to a different speaker. Radio reception is poor. The car antenna is not extended. Pull the antenna out all the way. The antenna control wire is not connected. Connect the wire correctly, referring to the section on "Connecting Wires to Terminals". The memory is erased when The battery wire has not been connected to the proper Connect the wire correctly, referring to the section on the ignition is turned off. terminal. "Connecting Wires to Terminals". The ignition and battery wire are incorrectly connected. Connect the wire correctly, referring to the section on "Connecting Wires to Terminals". A CD ejects as soon as it is The CD is upside-down. Load the CD with the labeled side up. loaded. The CD is quite dirty. Clean the CD, referring to the section on "Cleaning CDs" (see p. 6). The sound skips on a CD. The CD is scratched or dirty. Clean the CD, referring to the section on "Cleaning CDs" (see p. 6). A track will not play. Random play has been selected. Turn off random play. English — 24— External disc PROBLEM POSSIBLE CAUSE SOLUTION The disc control mode cannot No wire has been connected Connect the wire to the disc be selected. terminal on the unit. the unit. The specified disc does not The specified CD is quite dirty. Clean the CD. play, but another one plays instead. The CD is upside-down. Load the CD with the labeled side up. The disc is loaded in a different slot from that Eject the disc magazine and check the number specified disc. The disc is severely scratched. Try another disc instead. The sound skips. Something is touching the disc changer. Remove whatever is touching it. The CD is scratched or dirty. If skipping happens at the same place when the car is stopped, something with the CD is wrong. Clean the CD. The display shows that the The computer chip in the unit is not functioning normally. Press the reset button on the unit (see p. 5) . changer is being played, but no sound can be heard. The specified track will not Random play or magazine random play has been selected. Turn off random play or magazine random play. play. If the following situations, consult your nearest service center: • Even though the disc changer is connected, the Disc Changer Mode is not on, with "Mode. • Even though no device (KCA-S210A, CA-C1AX, KDC-CPS85, KDC-CX85, KDC-CPS82 or when switching modes. — 25— English Troubleshooting The following recommended No disc magazine ] Load the disc magazine No CD in the unit. ] Insert the CD. E-01 No disc has been loaded in the ] Load a disc into the disc magazine. E-02 E-04 No disc has been loaded in the disc ] Load a disc into the disc magazine. The CD is quite dirty. The CD is upside-down. ] Clean the CD ...
Questo manuale è adatto anche per i modelli :Unità - KDC-215S (315.68 kb)
Unità - KDC-315S (315.68 kb)
Unità - KDC-315V (315.68 kb)
Unità - KDC-35MR (315.68 kb)