valutazioni - 5, GPA: 4 ( )

Produttore : Kenwood File Size : 315.68 kb File Nome : Lingua di insegnamento:

• If the console has a lid, make sure to install the unit so that faceplate will not hit the lid when closing and opening. • If the fuse blows, first make sure the wires aren’t touching to cause a short circuit, then replace the old fuse with one with the same rating. • Do not let unconnected wires or terminals touch metal on the car or anything else conducting electricity. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. • After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. • Insulate unconnected wires with vinyl tape or other similar material. • Some disc changers need conversion cords for connection. See the section on "Safety Precautions" for details. • Mount the unit so that the mounting angle is 30° or less. — 19— Connecting KENWOOD disc Rear left output Front left output (White) Fuse (10A) (KDC-4015/415S only) To connect the Disc changer, consult your Disc changer English – + FRONT • L FRONT • R REAR • L REAR • R P.CONT.OUT ANT. CONT. 2CAUTION FM/AM antenna input Wiring harness (Accessory1) White/Black Gray/Black Green/Black Purple/Black White Gray Green Purple Power control/Motor antenna control wire (Blue/White) Ignition wire (Red) Battery wire (Yellow) Ground wire (Black) · (To car chassis) Ignition key switch ACC Car fuse box If no connections are made, do not let the wire come out from the tab. Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. NOTE Front right output (Red) (KDC-4015/415S only) Rear right output (Red) – To front left speaker To front right speaker + – + To rear left speaker To rear right – + – Car fuse box speaker + (Main fuse) Battery When only two speakers are being connected to the system, 2WARNING connect the connectors either to both the front output If you connect the ignition wire (red) and the battery wire terminals or to both the rear output terminals (do not mix (yellow) to the car chassis (ground), you may cause a short front and rear). For example, if you connect the + connector circuit, that in turn may start a fire. Always connect those wires of the left speaker to a front output terminal, do not connect to the power source running through the fuse box. the - connector to a rear output terminal. — 20— Installation Installation Installing Accessory4 Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and 1 Refer to the section “ Removing the hard ” Firewall or metal support and then remove the 2 Align the holes in the unit vehicle mounting bracket and accessory screws. T: Toyota cars N: Nissan cars Accessory5...for Nissan car Accessory6 ...for Toyota car 8 mm MAX. o5mm o5mm 8mm MAX. T N N T T/N 5 6 Self-tapping Accessory2 attach it in place. 2CAUTION screw Metal mounting • During installation, do not use any screws except for those (commerciall strap provided. The use of different screws might result in damage y available) the main unit. • Damage may occur if a screwdriver or similar tool is used with excessive force during the installations. NOTE Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). — 21— Installation Removing Removing English 1 Engage the catch locks on the lower level. Lower the frame and pull Catch Lock Accessory3 Removal tool 2 When the lower level is removed, remove the upper locations. The frame can be removed from the top side in the same manner. Accessory4 Lower the removal tool toward the bottom, and pull out the unit halfway whilst pressing towards the inside. 4 Pull the unit all the way out with your hands, being careful not to drop it. 5 Be careful to avoid injury from the catch pins on the removal tool. Catch facing up Refer to the section “ Removing the hard ” and then remove the Remove the Hex-head on the back panel. Insert the two removal tools deeply as shown. 3 2 1 Accessory3 Removal tool NOTE 2CAUTION — 22— Screwing If you want to fasten does not fall off, screw o4 . 16 mm) in the hole shown below. Accessory7 2CAUTION Never insert the taptite screw ( o4 . 16 mm) in any other screw hole than the one specified. If you screw it in another hole, contact and may cause damage to the mechanical parts inside the unit. — 23— Troubleshooting What might Before calling PROBLEM POSSIBLE CAUSE SOLUTION The power does not turn on. The fuse has blown. After checking for short circuits fuse with one with the same No sound can be heard, or the Attenuator is turned on. Turn off Attenuator. volume is low. The fader or balance settings are set all Reset the fader or balance settings. side. The input/output wires or wiring harness are Reconnect the input...

Scarica la tua

Per scaricare, digitare 2 cifre :