valutazioni - 4, GPA: 3.5
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
(For more information on finalization processing, refer to the manual for your CD-R/CD-RW writing software or CD-R/CD-RW recorder.) Additionally, depending on the recording status, it may prove impossible to play certain CDs recorded on CD-R or CD-RW. Do Not Use CDs with Sticker on the Labelled Side Do not use the CD with stuck on it. Using such a CD may cause deformed and the sticker to resulting in malfunction of the — 7— Switching Modes: Each time you press the SRC button, the mode switches as follows: Selecting the standby mode: Press the SRC button repeatedly to select to "ALL OFF". When "ALL OFF" is displayed, the standby mode is turned on. The standby mode turns all functions off although leaving the unit’s power on. Use this mode when you want to have the display illuminated but do not want to listen to anything. t Tuner mode t CD mode t External disc control mode 1 t External disc control mode 2 / AUX mode t Standby mode Switching Modes Turning on the power: Press the SRC button. Turn the power on before carrying out the following procedures. Turning off the power: Hold down the PWR OFF button for one second or more. The status of the Code Security Function (page 28) is displayed whenever the power is switched on. "CODE ON" : Security Code has been registered "CODE OFF" : Security Code has not been registered NOTE NOTE Power General features — 8 — English ATT/LOUD AM/ NF 4 . 5 / ° Q SRC / PWR OFF CLK DISP FM KDC-6090R/KDC-5090R KDC-V6090R ATT indicator LOUD indicator ATT indicator LOUD indicator Clock indicator Clock indicator System Q indicator System Q indicator Release button Speaker Setting indicator Speaker Setting indicator NOTE Attenuator • The mode switches cannot be used. • The external disc control that is connected. • To enable the selection of External mode, you should connect optional (which allows you to select mode 2 and AUX mode) or CD changer KDC-CPS85, KDC-CX85, KDC-CPS82 switching adapter CA-C1AX (which allows mode only). During the AUX mode, "AUX" (or AUX-name in the display. When the CA-C1AX is being used, the AUX Mode will replace the External Disc Control Mode. • If you have selected Standby mode, the timer function turns the power off automatically will be activated. To find out how to set the time on the timer, and how to cancel the timer function, refer to the section on the Power OFF Timer function under Menu settings (page 35). The Power OFF Timer function is enabled only after the security code (page 28) is set up. NOTE Selecting AUX-name display Holding down the DISP button for two seconds or more during the AUX mode, AUX-name display is blinked for AUX-name selection mode. Pressing 4 or . button during this mode allows you to select "AUX" , "TV" , "VCP" , "GAME" or "PORTABLE" in the AUX mode. The AUX-name selection mode can be exited by pressing the DISP button or doing nothing for 10 seconds. This function allows Turning Attenuator On/Off: Press the ATT button to switch the attenuator When the attenuator is on, indicator blinks. When the attenuator is off, the level. NOTE Turning the volume up, or turning it all the the attenuator function. Loudness This function amplifies low and high tones when the volume turned down. The LOUD indicator lights up, when the loudness function is on. Turning Loudness On/Off: Hold down the LOUD button for one second or more to switch the loudness on and off. NOTE The loudness function does not affect non-fading pre-out. Volume Increasing Volume: Press the 5 button to turn up the volume. Decreasing Volume: Press the ° button to turn down the volume. — 9— General features Theft Deterrent English The faceplate can detached form the unit, Removing the Faceplate: 1 • When the control panel is visible: Press the release button. • When the control panel has been Press the upper side of the faceplate. 2 Holding the centre part of the faceplate, 3 Push back the bottom of the faceplate bracket until it locks. 2 CAUTION Do not set the right side of the faceplate first, when reattaching the faceplate. connector on the faceplate bracket to malfunction. 2 Press the right side of the faceplate until it Hiding the control panel: 1 Press the release button and slide open the faceplate. 2 Push upward the back of the control panel and reverse panel. NOTE The panel cannot be reversed when the faceplate is not attached. Opening the control panel: 1 Press the upper side of the faceplate. The faceplate will open. 2 Push the bottom of the control panel and close the faceplate. 2 CAUTION • Do not apply excessive force to the faceplate bracket without attaching the faceplate. Doing so will cause the faceplate bracket to be deformed. • Do not touch the connector on the faceplate bracket after removing the faceplate. Touching the connector may cause damage to the unit. NOTE • The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. For that reason, keep the faceplate in its special storage case whilst detached. • Do not expose the f...
Questo manuale è adatto anche per i modelli :Unità - KDC-5090R (822.02 kb)
Unità - KDC-V6090R (822.02 kb)