valutazioni - 3, GPA: 4.7
(
)
)
|
Facilità d'uso
3 Adjust each mode Press the 4/ . button. Please refer to the following for the adjusting values. 4 Press the AUD button to end the control mode. "Bass F" : Adjust the centre frequency of the bass. Setting values: 60 / factor is set to 1.00, 1.25 quality factor is set to 2.00) NOTE This mode is available only when on. (page31) "Bass" : Adjust the bass level. Setting values: - 8 – + 8 "Bass Q" : Adjust the Bass quality factor. Setting values: 1.00 / 1.25 / 1.50 / 2.00 "Kex"/"EC"/"dB" : Recalling the kenwood preset sound setting Press the preset buttons (#1-6). Settings: #1;Flat, #2;Rock, #3;Pops/Top40, #4;Jazz, #5;Easy, #6;Scan of #1-5 NOTE • This mode is available only when the Sound coordinate system is on. (page31) • You can call the following settings with this function; bass centre frequency, bass level, bass quality factor, bass extension, treble centre frequency, and treble level setting. Their setting values are different depending on the setting of the mobile preset plan mode. NOTE This mode is available only when the Sound coordinate system is on. (pagee31) "Bass EXT" : Switch the Bass Extend mode on/off. Setting values: ON / OFF (When the bass extend mode is set to on, low frequency response is extended by 20%.) NOTE This mode is available only when the Sound coordinate system is on. (page31) — 9— General features English "TreF" : Adjust the centre frequency of the treble. Setting values: 10.0 NOTE This mode is available only on. ( page31). "Treble" : Adjust the treble level. Setting values: - 8 – + 8 "Balance" : Adjust the balance level. Setting values: Left 15 – Right 15 "Fader" : Adjust the fader level. Setting values: Front 15 – Rear 15 "V OFFSET" : Set the sound level of the each source selected by adjusting the level difference between the basic sound level and the required level. Setting values: - 8 – ± 0 Storing your sound settings: Hold down a preset button (#1-6) for two seconds or more except during the bass center frequency, bass level, bass quality factor, bass treble level adjust NOTE • This setting can be made system is on. (page31) • The settings you can preset level, bass quality factor, bass frequency, and treble level. Recalling your sound settings: Press a preset button (#1-6) except during the bass frequency, bass level, bass quality factor, bass extension, treble center frequency, and treble level adjust mode. NOTE This mode is available only when Sound coordinate system Mobile Preset This function allows you to adjust the setting that is recalled with the sound coordinate system, according to types of speakers. 1 Press the SRC button repeatedly to select the standby mode. "ALL OFF" is displayed when the standby mode is selected. 2 Press the AUD button to enter the mobile preset plan mode. 3 Press either the 4 or . button to select the type of speaker. The setting switches as follows. Off / For the OEM speaker / For 6/6x9 in. speaker / For 5/4 in. speaker 4 Press the AUD button to end the mobile preset plan mode. NOTE • This mode is available only when the Sound coordinate system is on. (page31) — 10 — • When you change treble tone settings Switching Display You can change the display in Changing the Display: Each time you press the CLK button, the follows: Mode display Clock Date "CALL" disappears original source is Turning TEL Mute Function Off After Phone Call: Hang the phone up. "CALL" disappears from the The original source (i.e., the returned to automatically, and Faceplate Angle Adjustment You can adjust the faceplate angle for easy Adjusting faceplate angle: Press the A (EJECT) button to make the faceplate slide open, and then adjust the faceplate angle using the angle adjustment switch. Adjustment may be made from 0 to 2. NOTE The . indicator lights whilst the clock is displayed. TEL Mute Shut down the audio system temporarily whenever an incoming call is received. NOTE The function will not work if a cable is not connected to the car phone. When the telephone rings: When a call is received, "CALL" is displayed and all the unit functions are temporarily interrupted. Restoring Original Unit Source During Phone Call: Press the SRC button. 0 1 2 0 1 2 02 1 NOTE • Firmly slide the switch until it clicks. • Do not apply excessive force to the faceplate under settings 1 or 2. • Set the angle adjustment switch to "0" before removing the faceplate. — 11 — General features English Removing the The faceplate can theft. Removing the faceplate: 1 Choose the way from among faceplate. Turn the ignition off, hold down the or more, or press the left part at the faceplate (as illustrated on p.13) for as preset in the "Manual Open Button Setting" the menu when the control panel has been 2 Set the faceplate's angle adjustment switch to faceplate angle to the vertical. For details, refer to "Faceplate Angle Adjustment" (. NOTE If the faceplate's angle adjustment switch is not set to "0" mounting the faceplate on the faceplate bracket, it may be difficult to mount the faceplate or the fa...
Questo manuale è adatto anche per i modelli :Unità - KDC-7080R (534.73 kb)