Log:
valutazioni - 3, GPA: 3.3 ( )

Istruzioni per l'uso Kenwood, Modello KDC-B7021

Produttore : Kenwood
File Size : 3.34 mb
File Nome :
Lingua di insegnamento: en
Vai a scaricare



da questo dispositivo ha anche altre istruzioni :

Facilità d'uso


Unit Vehicle Ignition wire (Red) A–7 Pin (Red) Connect to a power source Battery wire (Yellow) that can be turned on and off with the ignition key. Installtion Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Metal mounting strap (commercially available) Self-tapping screw (commercially available) Firewall or metal support Screw (M4X8) (commercially available) Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). To attach this unit, make sure the front of the control panel faces you and fit it into the mounting sleeve by pressing the four corners of the hard rubber frame at the same time. Do not apply strong pressure to other sections than the corners; otherwise troubles such as the impossibility of opening or closing the panel may result. — 32 — Removing Locking Removing Locking Accessory4 Removal tool Screw (M4X8) 2 Remove the screw (M4.8) on the back panel. 3 Insert the two removal tools deeply into the slots on each side, as shown. 4 Push upward the removal tool toward the top, and pull out the unit halfway while pressing towards the inside. Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. (commercially available) Accessory2 Removal tool If you want to off, follow the directions 1 Refer to the function "remove the faceplate. 2 Insert the provided screw into bottom side of the faceplate which unit. Accessory5 3 Refer to the section "Removing the faceplate" (page then reattaching the faceplate. Never insert the taptite screws (o2 X 4 mm) in any other screw holes than the one specified. If you insert it in another hole, it will contract may cause damage to the mechanical parts inside the unit. — 33 — English English What might just be the result Before calling service, for possible problems. General ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, one with the same rating. . No ACC position on vehicle ignition. . Connect the same wire to the ignition as the battery ? If you have selected Standby mode, the power will automatically. . The Power OFF Timer function has been activated. . If you do not want the power to go OFF automatically, cancel the Power OFF Timer function. ? Nothing happens when the buttons are pressed. . The computer chip in the unit is not functioning normally. . Press the reset button on the unit (page 4). ? There’s a source you can’t switch. . There’s no CD inserted. . Set the media you want to listen to. If there’s no media in this unit, you can't swhich to each source. . The Disc changer isn’t connected. . Connect the Disc changer. If the Disc changer isn’t connected to it's input terminal, You can't switch to an external disc source. ? The faceplate does not open or close. . The faceplate is incorrectly attached. . Reattach the faceplate correctly, See the section on (page 11). ? The memory is erased when the ignition is turned OFF. . The battery wire has not been connected to the proper terminal. . Connect the wire correctly, referring to the section on . . The ignition and battery wire are incorrectly connected. . Connect the wire correctly, referring to the section on . ? The TEL mute function . The TEL mute wire . Connect the wire correctly, referring to the section . ? The TEL mute function turns not connected. . The TEL mute wire is touching a metal . Pull the TEL mute wire away from the ? Even if Loudness is turned ON, high-pitched for. . Tuner source is selected. . High-pitched tone isn't compensated for when in source. ? The Bass center frequency, Bass quality factor, Bass extend, Middle center frequency, Middle quality factor, and Treble center frequency can’t be adjusted. . The (page 25) is set OFF. . Set it ON. ? No sound can be heard, or the volume is low. . The fader or balance settings are set all the way to one side. . Center the fader and balance settings. . The input/output wires or wiring harness are connected incorrectly. . Reconnect the input/output wires or the wiring harness correctly. See the section on . . The values of Volume offset are low. . Increase the values of Volume offset. (page 9) — 34 — ? The sound quality ? The sound quality . Check the speaker wiring. . The speakers are not wired . Reconnect the speaker wires connected to a different speaker. ? The Mask Key item isn’t displayed in the Menu System. . The Mask Key function is already activated. . When the Mask Key function is activated displayed in the menu items. ? The Touch Sensor Tone doesn’t sound. . The preout jack is being used. . The Touch Sensor Tone can’t be output from the preout jack. ? Even though Synchronize Clock is ON, the clock can’t be adjusted. . The recei...

Questo manuale è adatto anche per i modelli :
Unità - KDC-7021 (3.34 mb)
Unità - KDC-V7521 (3.34 mb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie