valutazioni - 1, GPA: 5
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
• After the unit is installed, check whether the brake indicators, wipers, etc. on the car are working properly. • If the console has a lid, make sure to install the faceplate does not hit the lid when closing • Mount the unit so that the mounting angle or less. — 22 — Connecting Wires to Terminals 14 Connecting Wires to Terminals 14 To connect the Disc changer, consult your Antenna Conversion Adaptor Disc changer manual. (ISO–JASO) (Accessory3) To Steering remote (Blue/Yellow) Antenna Cord (ISO) (Optional Accessory) REAR L R REMO.CONT Connector Function Guide Pin Numbers for ISO Connectors Wire Color Functions External Power Connector A–4 A–5 A–7 A–8 Yellow Blue/White Red Black Battery Power Control Ignition (ACC) Earth (Ground) Connection Speaker Connector B–1 B–2 B–3 B–4 B–5 B–6 B–7 B–8 Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black Rear Right (+) Rear Right (–) Front Right (+) Front Right (–) Front Left (+) Front Left (–) Rear Left (+) Rear Left (–) — 23 — 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 P.CONT ANT.CONT TEL MUTE Battery wire (Yellow) Ignition wire (Red) FM/AM antenna input Wiring harness (Accessory1) If no connections are made, do not let the wire come out from the tab. Power control/ Motor antenna control wire (Blue/White) A–7 Pin (Red) A–4 Pin (Yellow) Connector A Connector B Fuse (10A) See page 24 TEL mute wire (Brown) Connect to the terminal that is grounded when either the telephone rings or during conversation. To connect the KENWOOD navigation system, consult your navigation manual. Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. English English 2WARNING Connecting the ISO Connector (see p.23) The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated. Please be sure to reconnect the cable as shown 2 below to install this unit to the Volkswagen vehicles etc. 1 (Default setting) The A-7 pin (red) of the vehicle's ISO connector is linked with the ignition, and the A-4 pin (yellow) is connected to the constant power supply. Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) 2 The A-7 pin (red) of the vehicle's ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition. Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) 3 The A-4 pin (yellow) of the vehicle's ISO connector connected to anything, while the A-7 pin (red) constant power supply (or both the A-7 (are connected to the constant power supply). Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) When the connection is 3 above, the unit's power be linked to the ignition For that reason, always off the unit's power To link the unit's power (ACC...red) Installation ¦ Installation Firewall or metal support Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Metal mounting strap (commercially available) Self-tapping screw (commercially available) Screw (M4X8) (commercially available) Make sure that the unit is installed securely in place. If the unit unstable, it may malfunction (eg, the sound may skip). ignition key. — 24 — ¦ ¦ 1 Engage the catch pins on the removal tool and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. Catch Lock Accessory2 Removal tool 2 When the lower level is removed, remove the upper two locations. ¦ Removing the Unit 1 Refer to the section “Removing the hard rubber frame” and then remove the hard rubber frame. 2 Remove the screw (M4.8) on the back panel. 3 Insert the two removal tools deeply into the slots on each side, as shown. Screw (M4X8) (commercially available) Accessory2 Removal tool 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Be careful to avoid injury from the catch pins 5 Pull the unit all the way out with your hands, being careful not to drop it. The frame can be removed from — 25 — English English What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, replace the fuse with one with the same rating. . No ACC position on vehicle ignition. . Connect the same wire to the ignition as the battery wire. ? Nothing happens when the buttons are pressed. . The computer chip in the unit is not functioning normally. . Press the reset button on the unit (page 4). ? There’s a source you can’t switch....
Questo manuale è adatto anche per i modelli :Unità - KDC-3027A (925.21 kb)
Unità - KDC-3027G (925.21 kb)
Unità - KDC-308A (925.21 kb)
Unità - KDC-308G (925.21 kb)