valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
2 Press or repeatedly to select the item to be adjusted: • [BALANCE] (balance) range: 12L to 12R. (L=left speaker, R=right speaker) • [FADER] (fader) range: 12R to 12F. (R=rear speaker, F=front speaker) • [BASS] (bass) range: -7 to +7. • [TREBLE] (treble) range: -7 to +7. 3 Rotate to adjust the setting. 10 Adjust system settings 1 Press MENU to access system settings. 2 Press or repeatedly until one of the following settings scrolls. • [BEEP], [DIMMER], [DEMO], [BLACK OUT], or [DANCE] 3 Rotate to change the setting. [BEEP] [BEEP ON] Enable the beep sound of buttons. [BEEP OFF] Disable the beep sound of buttons. [DIMMER] [DIMMER HIGH] Increase the brightness level of the screen. [DIMMER LOW] Decrease the brightness level of the screen. [DEMO] [DEMO ON] Demonstrate all features after the system stays inactive for 2 minutes. [DEMO OFF] Disable the demo mode. [BLACK OUT] [BKO 10 S] Turn off the screen automatically 10 seconds after last operation. [BKO 20 S] Turn off the screen automatically 20 seconds after last operation. [BKO OFF] Never turn off the screen. [DANCE] [DANCE ON] Enable the spectrum on the LCD display. [DANCE OFF] Disable the spectrum on the LCD display. EN 11 Additional information Reset You can reset the unit to its default setting. 1 Detach the front panel. 2 Press the RESET button with the tip of a ball-point pen or toothpick. »»All settings are reset to factory default. Replace fuse If there is no power, check the fuse and replace if it is damaged. 1 Check the electric connection. 2 Remove the damaged fuse from the rear panel. 3 Insert a new fuse with the same specification (15A). Note ••If the new fuse gets damaged again, there may be an internal malfunction. Consult your Philips dealer. English EN 12 Product information Note ••Product information is subject to change without prior notice. Power supply 12 V DC (11 V - 16 V), negative ground Fuse 15 A Suitable speaker impedance 4 - 8 Maximum power output 50 W x 4 channels Continuous power output 21 W x 4 RMS (4 10% T.H.D.) Pre-Amp output voltage 2.5V Aux-in level 500 mV Dimensions (W x H x D) 181.5 x 52 x 191.4 mm Weight 1.47 kg Radio Frequency range - FM 87.5 - 108.0 MHz Frequency range - AM(MW) 522 - 1620 KHz (9 kHz) 530 - 1710 kHz (10 kHz) Usable sensitivity - FM 8 .V Usable sensitivity - AM(MW) 30 .V Compatible USB devices: • USB flash memory: USB 1.1 host with interface reading all speed support (1.1, 2.0) • USB flash players: USB 1.1 host with interface reading all speed support (1.1, 2.0) Supported formats: • USB or memory file format: FAT12, FAT16, FAT32 • For USB storage devices: MP3 bit rate (data rate): 32-320 Kbps and variable bit rate • WMA V4, V7, V8, V9 (L1, L2) • MP3 sampling frequencies: 8-48 kHz • For Disc: MP3 Bit-rates: 8~320 (kbps), variable bit rates • WMA sampling frequencies: 32 kHz, 44.1 kHz, 48 kHz • WMA Bit-rates: 32~192 (kbps), variable bit rates • Directory nesting up to a maximum of 8 levels • Number of albums/folders: CD maximum 99, USB or memory maximum 99 • Number of tracks/titles: CD maximum 999 (depending on number of album), USB or memory maximum 999 • ID3 tag v2.0 or later Unsupported formats: • Empty albums: an empty album is an album that does not contain MP3/ WMA files, and is not be shown in the display. • Unsupported file formats are skipped. For example, Word documents (.doc) or MP3 files with extension .dlf are ignored and not played. • AAC, WAV, PCM audio files • DRM protected WMA files (.wav, .m4a, .m4p, .mp4, .aac) • WMA files in Lossless format EN 13 Troubleshooting Caution ••Never remove the casing of this apparatus. To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this apparatus, check the following points before requesting service. If the problem remains unsolved, go to the Philips web site (philips.com/support). When you contact Philips, ensure that your apparatus is nearby and the model number and serial number are available. No power or no sound. ••Car engine is not on. Turn the car engine on. ••Cable is not correctly connected. Check connections. ••Fuse is burnt. Replace fuse. ••Volume is too low. Adjust volume. ••If the above solutions cannot help, press RESET button. ••Ensure that the track played is of a compatible format. Noise in broadcasts. ••Signals are too weak. Select other stations with stronger signals. ••Check the connection of the car antenna. ••Change broadcast from Stereo to mono. Cannot play disc ••Ensure that the disc label is inserted with the printed side facing up. ••Wipe the disc with fibre cleaning cloth from the centre to the edge in a straight line. ••This disc may be defective. Play another disc. ••Ensure that the CD is a finalised CD/ CD-R/CD-RW. ••Ensure that the CD is not encoded with copyright protection technologies. The CD skips tracks ••Ensure that the CD is not damaged or dirty. ••Ensure that random mode is deactivated. Disc cannot be ejected ••Press and hold . Preset stations lost. ••Battery ...