valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
• Access system menu. d / • Turn the unit on or off. • Confirm selection. • Mute or unmute sound. • Rotate to adjust volume. e ZONE / • Select tuner band. • Select MP3/WMA folder. • Press and hold to switch music listening zone. English EN f • Eject disc. g • USB socket. h AUDIO IN • Connect external audio device. i ............ / • Turn on or off maximum sound feature. • In any mode, press and hold to view clock. j DBB/AS • Press to turn on or off Dynamic Bass Boost (DBB) sound. • In radio mode, press and hold to access to tuner auto store. k / • Start, pause, or resume the play of tracks. • In radio mode, press to select the preset radio station of No. 5/6. • In radio mode, press and hold to store the current radio station at channel No. 5/6. l / • In radio mode, press to select the preset radio station of No. 3/4. • In radio mode, press and hold to store the current radio station at channel No. 3/4. • For .wma and .mp3 tracks, press repeatedly to select shuffle play/repeat play. m / • In radio mode, press to select the preset radio station of No. 1/2. • In radio mode, press and hold to store the current radio station at channel No. 1/2. • For .wma and .mp3 tracks on a storage device, press to access the track/folder list. n SOURCE/DISPLAY • Press repeatedly to select source. • Display current status. • Press and hold to select the dimmer high or low. o • Press repeatedly to select a preset equalizer (EQ). • Press and hold to access audio setting menu. p • Unlock the panel. q • Press to hang up a call. • Press and hold to reject an incoming call. r RESET • Restore default settings. s Disc slot EN 3 Install the car audio These instructions are for a typical installation. However, if your car has different requirements, make the corresponding adjustment. If you have any questions regarding installation kits, consult your Philips car audio dealer. Caution ••This unit is designed for negative ground (earth) 12 V DC operation only. ••Always install this unit in the car dashboard. Other locations can be dangerous as the rear of the unit heats up during use. ••To avoid short-circuit: before you connect, ensure that the ignition is off. ••Ensure that you connect the yellow and red power supply leads after all other leads are connected. ••Ensure that all loose leads are insulated with electrical tape. ••Ensure that the leads do not get caught under screws orin parts that will move (e.g. seat rail). ••Ensure that all ground (earth) leads are run to a common ground (earth) point. ••Use only the supplied mounting hardware for a safe and secure installation. ••Improper fuses can cause damage or fire. When you need to change the fuse, consult a professional. Note on the power supply lead (yellow) • When you connect other devices to this apparatus, ensure that the rating of the car circuit is higher than the total fuse value of all the connected devices. Notes on speaker connection • Never connect speaker wires to the metal body or chassis of the car. • Never connect speaker wires with stripes to one another. Connect wires Caution ••Ensure that all loose leads are insulated with electrical tape. Note ••Consult a professional to connect CEM2220BT as instructed below. 1 Check the car's wiring carefully and connect them to the the supplied male connector. Note ••Risk of danger! Please consult a professional to perform the below steps! ISO male connectors Connect to 1 Green strip, black- edged green strip Left speaker (Rear) 2 White strip, black- edged white strip Left speaker (Front) 3 Gray strip, black- edged gray strip Right speaker (Front) 4 Purple strip, black- edged purple strip Right speaker (Rear) English EN ISO male connectors Connect to e Red Ignition key +12V DC when ON/ACC f Blue Motor/electric antenna relay control lead g White edged blue strip Amplifier relay control lead h Black Ground i Yellow To the +12V car battery which is energized at all times 2 Connect the antenna and amplifier as illustrated, if applicable. Connector Connect to 1 ANTENNA Antenna 2 Socket for ISO male connectors As indicated in Step 1 above 3 REAR LINE OUT R (Socket) Rear right speaker 4 REAR LINE OUT L (Socket) Rear left speaker 5 OE REMOTE (Purple) OE Remote Tip ••The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Be sure to make proper connections to prevent damage to the unit. Mount into the dashboard 1 If the car does not have an on-board drive or navigation computer, disconnect the negative terminal of the car battery. • If you disconnect the car battery in a car that has an on-board drive or navigation computer, the computer may lose its memory. • If the car battery is not disconnected, to avoid short-circuit, ensure that the bare wires do not touch each other. 2 Ensure that car dashboard opening is within these measurements: 183 mm53mm5mm 3 Remove the mounting sleeve with the supplied disassembly tools. EN 4 Install the sleeve into the dashboard and bend the tabs outward to fix the sleeve. Note...