valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
In “FRT1” mode, bass adjustment affects only the rear output: front output cannot be adjusted. 1. Press the AUDIO button and select the Bass mode (BASS) in the Audio Menu. 2. Select the desired frequency with the 2/3buttons. 40 i63 i100 i160 (Hz) 3. Boost or attenuate the bass level with the 5/°buttons. The display shows “+6” – “–6”. Treble Adjustment (TRE) You can adjust the cut-off frequency and the Treble level. In “FRT1” and “FRT2” modes, treble adjustment affects only the front output: rear output cannot be adjusted. 1. Press the AUDIO button and select the Treble mode (TRE) in the Audio Menu. 2. Select the desired frequency with the 2/3buttons. 2K i4K i6K i10K (Hz) 3. Boost or attenuate the treble level with the 5/°buttons. The display shows “+6” – “–6”. ENGLISH ESPANOL DEUTSCH FRANCAIS ITALIANO NEDERLANDS 28 Audio Adjustment Loudness Adjustment (LOUD) The Loudness function compensates for deficiencies in the low and high sound ranges at low volume. You can select a desired Loudness level. 1. Press the AUDIO button and select the Loudness mode (LOUD) in the Audio Menu. 2. Switch the Loudness function ON/OFF with the 5/°buttons. “LOUD” 3. Select the desired level with the 2/3buttons. LOW (low) +=MID (mid) += HI (high) Subwoofer Output (SUB.W) When a Subwoofer is connected, switch Subwoofer output ON. Initially, Subwoofer output is ON. 1. Press the AUDIO button and select the Subwoofer ON/OFF mode (SUB.W) in the Audio Menu. 2. Switch the Subwoofer output ON/OFF with the 5/. buttons. Note: • When the Rear Output setting is “FRT+REAR”, you cannot switch the Subwoofer ON/OFF mode. (Refer to page 34.) “SW” 29 Subwoofer Setting Adjustment (80HZ 0) When the Subwoofer output is ON, you can adjust the cut-off frequency and the output level of Subwoofer. 1. Press the AUDIO button and select the Subwoofer setting mode (80HZ 0) in the Audio Menu. 2. Select the frequency to 50 Hz, 80 Hz or 125 Hz with the 2/3 buttons. 3. Increase or decrease the output level with the 5/°buttons. The display shows “+6” – “–6”. Note: • You can select the Subwoofer setting mode only when Subwoofer output is switched ON in the Subwoofer ON/OFF mode. Source Level Adjustment (SLA) The SLA (Source Level Adjustment) function prevents radical leaps in volume level when switching between sources. Settings are based on the FM volume level, which remains unchanged. 1. Compare the FM volume with the volume of the other source. (e.g. Built-in CD player.) 2. Press the AUDIO button and select the SLA mode (SLA) in the Audio Menu. 3. Increase or decrease the level with the 5/°buttons. The display shows “+4” – “–4”. Note: • Since the FM volume is the control, SLA is not possible in the FM modes. • The MW/LW volume level, which is different from the FM base setting volume level, can also be adjusted similar to sources other than tuner. ENGLISH 30 Detaching and Replacing the Front Panel Theft Protection The front panel of the head unit is detachable to discourage theft. • Keep the front panel closed while driving. Detaching the Front Panel 1. Open the front panel. 2. Grip and pull the front panel gently outward. Take care not to grip it tightly or drop it. 3. Use the protective case provided to store/carry the detached front panel. Replacing the Front Panel • Replace the front panel by holding it upright to this product and clipping it securely into the mounting hooks. Precaution: • Never use force or grip the display tightly when removing or replacing the front panel. • Avoid subjecting the front panel to excessive shocks. • Keep the front panel out of direct sunlight and high temperatures. Warning Tone If the front panel is not detached within 5 seconds after the ignition is turned off, a warning tone will sound. Note: • You can cancel the warning tone function. (Refer to page 33.) 31 Initial Setting ENGLISHEntering the Initial Setting Menu With this menu, you can perform initial settings for this product. 1. Turn the source OFF. 2. Enter the Initial Setting Menu. Hold for 2 seconds 3. Select a desired mode. Each press changes the Mode ... 4. Operate a mode. 5. Cancel the Initial Setting Menu. Note: • Holding down the FUNCTION button for 2 seconds also cancels the Initial Setting Menu. 32 Initial Setting Initial Setting Menu Functions The Initial Setting Menu features the following functions. Changing the FM Tuning Step (FM STEP) Normally set at 50 kHz during Seek tuning in the FM mode, the tuning step changes to 100 kHz when the AF or TA mode is activated. It may be preferable to set tuning step to 50 kHz in the AF mode. 1. Press the FUNCTION button and select the FM Tuning Step mode (FM STEP) in the Initial Setting Menu. 2. Select the desired tuning step with the 2/3buttons. Note: • The tuning step remains set at 50 kHz during Manual tuning. • The tuning step returns to 100 kHz if the battery is temporarily disconnected. Switching the Auto PI Seek (A-PI) During Preset Station PI Seek operation, you can switch the Auto PI Seek function ON/OFF. (Ref...
Questo manuale è adatto anche per i modelli :Unità - DEH-3330R (2.07 mb)