valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
1 Recall the equalizer curve you want to adjust. 2 Push M.C. left or right to select the equalizer band to adjust. 100Hz—315Hz—1.25kHz—3.15kHz—8kHz 3 Push M.C. up or down to adjust the equalizer curve. +6 to –6 is displayed as the equalizer curve is increased or decreased. LOUD (loudness) Loudness compensates for deficiencies in the low- and high-frequency ranges at low volume. 1 Press M.C. to turn loudness on or off. 2 Push M.C. left or right to select the desired set ting. Low (low)—Mid (mid)—High (high)—OFF (off) Sub W.1 (subwoofer on/off setting) This unit is equipped with a subwoofer output which can be turned on or off. 1 Press M.C. to turn subwoofer output on or off. 2 Push M.C. left or right to select the phase of sub- woofer output. Push M.C. left to select reverse phase and Reverse appears in the display. Push M.C. right to select normal phase and Normal appears in the display. Sub W.2 (subwoofer adjustment) When the subwoofer output is on, you can adjust the cut-off frequency and the output level of the subwoofer. Only frequencies lower than those in the selected range are outputted from the subwoofer. 1 Push M.C. left or right to select cut-off frequency. 50Hz—63Hz—80Hz—100Hz—125Hz 2 Push M.C. up or down to adjust the output level of the subwoofer. Each time M.C. is pushed up or down, subwoofer level increases or decreases. +6 to -24 is displayed as the level is increased or decreased. Bass (bass boost) 1 Push M.C. up or down to select a desired level. 0 to +6 is displayed as the level is increased or decreased. HPF (high pass filter adjustment) When you do not want low sounds from the subwoofer output frequency range to play from the front or rear speakers, turn on the HPF (high pass filter). Only frequencies higher than those in the selected range are output from the front or rear speakers. 1 Press M.C. to turn high pass filter on or off. 2 Push M.C. left or right to select cut-off frequency. 50Hz—63Hz—80Hz—100Hz—125Hz SLA (source level adjustment) SLA (Source level adjustment) lets you adjust the volume level of each source to prevent radical changes in volume when switching between sources. ! Settings are based on the FM volume level, which remains unchanged. Before adjusting source levels, compare the FM volume level with the level of the source you wish to adjust. ! The MW/LW volume level can also be adjusted with source level adjustments. 1 Push M.C. up or down to adjust the source volume. Adjustment range: +4 to –4 Note When selecting FM as the source, you cannot switch to SLA. Initial Settings 1 1 Function display ! Shows the function status. 1 Press SRC/OFF and hold until the unit turns off. 2 Press M.C. and hold until the initial setting menu appears in the display. Operating this unit 15 En Section 02 Operating this unit 3 Turn M.C. to select the initial setting. After selecting, perform the following procedures to set the initial setting. Language select (multi language) For your convenience, this unit equips multiple language display. You can select the language best suited to your first language. 1 Press M.C. to select the language. English—Francais—Italiano—Espanol— Deutsch—Nederlands—РУССКИЙ Calendar (setting the date) 1 Push M.C. left or right to select the segment of the calendar display you wish to set. Year—Day—Month 2 Push M.C. up or down to set the date. Clock (setting the clock) 1 Push M.C. left or right to select the segment of the clock display you wish to set. Hour—Minute 2 Push M.C. up or down to put a clock right. ! You can match the clock to a time signal by pressing M.C. ! If 00 to 29, the minutes are rounded down. (e.g., 10:18 becomes 10:00.) ! If 30 to 59, the minutes are rounded up. (e.g., 10:36 becomes 11:00.) EngineTime alert (elapsed time display setting) This setting allows you to measure the length of time that elapses from when the machine is turned on and display the amount of elapsed time per set period. Also, you will hear alarm. 1 Press M.C. to select your favorite setting. OFF—15Minutes—30Minutes FM step (FM tuning step) Normally the FM tuning step employed by seek tuning is 50 kHz. When AF or TA is on, the tuning step automatically changes to 100 kHz. It may be preferable to set the tuning step to 50 kHz when AF is on. 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the FM tuning step. 50kHz (50 kHz)—100kHz (100 kHz) Auto PI (auto PI seek) The unit can automatically search for a different station with the same programming, even during preset recall. 1 Press M.C. to turn Auto PI seek on or off. USB plug&play (plug and play) This setting allows you to switch your source to USB/ IPOD automatically. 1 Press M.C. to turn the plug and play on or off. ! ON – When USB storage device/iPod is connected, the source is automatically switched to USB/IPOD. If you disconnect your USB storage device/iPod, this unit’s source is turned off. ! OFF – When USB storage device/iPod is connected, the source is not switched to USB/ IPOD automatically. Please ...