valutazioni - 1, GPA: 4
(
)
)
|
Facilità d'uso
Install the unit into the dashboard. Insert the mounting sleeve into the dashboard. And then secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place. 182 53 Dashboard Side bracket Screw (2 mm . 3 mm) Mounting sleeve DIN Rear-mount 1. Determine the appropriate position where the holes on the bracket and the side of the unit match. • When installing in a shallow space, use the following screw holes. *1 Use binding screws (4 mm . 3 mm) only. *1 *1 2. Tighten two screws on each side. Use any of binding screws (4 mm . 3 mm), binding screws (5 mm . 6 mm) or flush surface screws (5 mm . 6 mm), depending on the shape of screw holes in the bracket. Screw Dashboard or Console Factory radio mounting bracket Removing the unit Extend top and bottom of the trim ring outwards to remove the trim ring. And then loosen the screws (2 mm . 3 mm) to remove the mounting sleeve. • When reattaching the trim ring, push the trim ring onto the unit until it clicks after reattaching the mounting sleeve. (If the trim ring is attached upside down, the trim ring will not fit properly.) Mounting sleeve Trim ring Screw (2 mm . 3 mm) Fastening the front panel If you do not plan to detach the front panel, the front panel can be fastened with supplied screw. Screw Installation Installation LCD panel Leave gap Dashboard Do not cover this area. When connecting the external video component and the display This product External video component (sold separately) RCA cables (sold separately) Audio input (AUDIO INPUT) Video input (VIDEO INPUT) 13 cm Display with RCA input jacks (sold separately) Rear monitor output (REAR MONITOR OUTPUT) To video input To video output To audio outputs 13 cm Rear audio output (REAR MONITOR OUTPUT(AUDIO)) To audio input 17 cm RCA cables (sold separately) Mini pin plug cable (sold separately) • It is necessary to change AV Input in System Menu when connecting the external video component. When using a display connected to rear video output This product’s rear video output and rear audio output are for connection of a display to enable passengers in the rear seats to watch the DVD, etc. WARNING Never install the display in a location where it is visible to the driver while driving. Connecting the units Leave ample space Dash board Connecting and installing the optical cable connection box WARNING • Avoid installing the optical cable connection box in locations where the operation of safety devices such as airbags is prevented by this unit. Otherwise, there is a danger of a fatal accident. • Avoid installing the optical cable connection box in locations where the operation of the brake may be prevented. Otherwise, it may result in a traffic accident. • Fix the optical cable connection box securely with the hook and loop fastener or lock tie. If the unit is loose, it disturbs driving stability, which may result in a traffic accident. CAUTION • Install this unit using only the parts supplied with this unit. If other parts are used, this unit may be damaged or could dismount itself, which leads to an accident or other problems. • Do not install this unit near the doors where rainwater is likely to be spilled on the unit. Incursion of water into the unit may cause smoke or fire. Connecting the optical cable 1. Connect the optical cable and ground lead to the main unit. Connect the optical cable so that it does not protrude from the main unit, as shown in the illustration. Fasten the ground lead to the protrusion on the back of the main unit. Screw 2. Connect the optical cable to the optical cable connection box. optical cable Installing the optical cable connection box • When installing the optical cable connection box with the hook and loop fastener. Install the optical cable connection box using the hook and loop fastener in the ample space of the console box. Hook fastener Loop fastener • When installing the optical cable connection box with the lock tie. Wrap the optical cable and connection box with the protection tape and fasten with the power code using the lock tie. Wrap with the protection tape Fasten with the lock tie Connecting the units Installation Installation Installing the microphone Install the microphone in a position and orientation that will enable it to pick up the voice of the person operating the system. CAUTION • It is extremely dangerous to allow the microphone lead to become wound around the steering column or gearstick. Be sure to install the unit in such a way that it will not obstruct driving. When installing the microphone on the sun visor 1. Install the microphone on the microphone clip. Microphone Microphone clip 2. Install the microphone clip on the sun visor. • With the sun visor up, install the microphone clip. (Lowering the sun visor reduces the voice recognition rate.) Microphone clip Clamp • Use separately sold clamps to secure the lead where necessary inside the vehicle. When installing the microphone on the steering column 1. Install the microphone on t...
Questo manuale è adatto anche per i modelli :Unità - AVH-P5200BT (1.48 mb)