N‡IIOA UOU.OEOU‚O OOOU‚AUOU‚UAU IO‚.I U.A·O‚‡IEflI I .‚AUU O.O‚O‰O‚. Printed in Japan Imprime au Japon RE <06C00000> eiaeCeNeiCe ee ieiAceCaO WARNING To avoid the risk of accident and the potential violation of applicable laws, the front DVD or TV • PIONEER does not recommend that you (sold separately) feature should never be used install or service your display yourself. while the vehicle is being driven. Also, Rear Installing or servicing the product may Displays should not be in a location where it is a expose you to risk of electric shock or visible distraction to the driver. other hazards. Refer all installation and • In some countries or states the viewing of images servicing of your display to authorized on a display inside a vehicle even by persons other than the driver may be illegal. Where such regula- Pioneer service personnel. tions apply, they must be obeyed and this unit's DVD features should not be used. • Secure all wiring with cable clamps or • LIGHT GREEN LEAD AT POWER CONNEC- electrical tape. Do not allow any bare TOR IS DESIGNED TO DETECT PARKED wiring to remain exposed. STATUS AND MUST BE CONNECTED TO THE POWER SUPPLY SIDE OF THE PARK • Do not drill a hole into the engine com- ING BRAKE SWITCH. IMPROPER CONNEC partment to connect the yellow lead of TION OR USE OF THIS LEAD MAY VIOLATE the unit to the vehicle battery. Engine APPLICABLE LAW AND MAY RESULT IN vibration may eventually cause the insu- SERIOUS INJURY OR DAMAGE. lation to fail at the point where the wire passes from the passenger compartment into the engine compartment. Take extra care in securing the wire at this point. • It is extremely dangerous to allow the display lead to become wound around the steering column or gearshift. Be sure to install the display in such a way that it will not obstruct driving. • Make sure that wires will not interfere with moving parts of the vehicle, such as the gearshift, parking brake or seat sliding mechanism. • Do not shorten any leads. If you do, the protection circuit may fail to work properly. Note: • When an external power amp is being used with • This unit is for vehicles with a 12-volt battery and this system, be sure not to connect the blue/white negative grounding. Before installing it in a recre-lead to the amp’s power terminal. Likewise, do not ational vehicle, truck, or bus, check the battery connect the blue/white lead to the power terminal voltage. of the auto-antenna. Such connection could cause • To avoid shorts in the electrical system, be sure to excessive current drain and malfunction. disconnect the . battery cable before beginning • To avoid short-circuit, cover the disconnected lead installation. with insulating tape. Insulate the unused speaker • Refer to the owner’s manual for details on leads without fail. There is a possibility of a short- connecting the power amp and other units, then circuit if the leads are not insulated. make connections correctly. • To prevent incorrect connection, the input side of • Secure the wiring with cable clamps or adhesive the IP-BUS connector is blue, and the output side tape. To protect the wiring, wrap adhesive tape is black. Connect the connectors of the same around them where they lie against metal parts. colors correctly. • Route and secure all wiring so it cannot touch any • This unit cannot be installed in a vehicle that moving parts, such as the gear shift, handbrake and does not have an ACC (accessory) position on seat rails. Do not route wiring in places that get the ignition switch. (Fig. 1) hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle body. • Don’t pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead insulation and cause a very dangerous short. • Do not shorten any leads. If you do, the protection circuit may fail to work when it should. ON START OFFACC ON START OFF ACC position No ACC position • Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of Fig. 1 the lead will be exceeded, causing overheating. • When replacing the fuse, be sure to only use a fuse • The black lead is ground. Please ground this lead of the rating prescribed on the fuse holder. separately from the ground of high-current prod • Since a unique BPTL circuit is employed, never ucts such as power amps. wire so the speaker leads are directly grounded or If you ground the products together and the ground the left and right . speaker leads are common. becomes detached, there is a risk of damage to the • If the RCA pin jack on the unit will not be used, do products or fire. not remove the caps attached to the end of the con nector. • Speakers connected to this unit must be high- power with minimum rating of 50 W and impedance of 4 to 8 ohms. Connecting speakers with out-• Cor...
Log: