valutazioni - 3, GPA: 4.7
(
)
)
|
Foto e specifiche Pioneer DEH-P700BT |
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
Power amp (sold separately) 33. Power amp (sold separately) ^-\- 12.Multi-CD player 11. IP-BUS cable (sold separately) 25. Blue/white Connect to system control terminal of the power amp (max. 300 mA 12 V DC). 26. Blue/white (7*) Connect to auto-antenna relay control terminal (max. 300 mA 12 V DC). 27. Blue/white (6*) The pin position of the ISO connector will differ depends on the type of vehicle. Connect 6* and 7* when Pin 5 is an antenna control type. In another type of vehicle, never connect 6* and 7*. 32. Connect with RCA cables (sold separately) 37. Subwoofer 38. Front 39. Rear t^| 38. Front speaker 39. Rear speaker ' 40. Perform these connections when using the optional amplifier. 24. Yellow/black If you use an equipment with Mute function, wire this lead to the Audio Mute lead on that equipment. If not, keep the Audio Mute lead free of any connections. 28. Speaker leads White: Front left © White/black: Front left © Gray: Front right © Gray/black: Front right © Green: Rear left © or subwoofer © Green/black: Rear left © or subwoofer © Violet: Rear right © or subwoofer © Violet/black: Rear right © or subwoofer © 41 Notes • Change the initial setting of this unit (refer to the operation manual). The subwoofer output of this unit is monaural. • When using a subwoofer of 70 W (2 Q), be sure to connect with Violet and Violet/black leads of this unit. Do not connect anything with Green and Green/black leads. Connecting the units ~) c English Note • When this unit is installed in a vehicle without ACC (accessory) position on the ignition switch, red cable must be wired to the terminal that can detect the operation ot the ignition key. Otherwise, battery drain may result. ACC position No ACC position Use this unit in other than the following conditions could result in tire or maltunction. — Vehicles with a 12-volt battery and negative grounding. — Speakers with 50 W (output value) and 4 ohm to 8 ohm (impedance value). To prevent short-circuit, overheating or maltunction, be sure to tollow the directions below. — Disconnect the negative terminal ot the battery before installation. — Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts. — Place all cables away trom moving parts, such as gear shitt and seat rails. — Place all cables away trom hot places, such as near the heater outlet. — Do not pass the yellow cable through a hole into the engine compartment to connect to a battery. — Cover any disconnected cable connectors with insulating tape. — Do not shorten any cables. — Never cut the insulation ot the power cable ot this unit in order to share the power to other equipment. Current capacity ot the cable is limited. — Use a tuse ot the rating prescribed. — Never wire the speaker negative cable directly to ground. — Never band together multiple speaker’s negative cables. Control signal is output through blue/white cable when this unit is powered on. Connect it to an external power amp’s system remote control or the vehicle’s auto-antenna relay control terminal (max. 300 mA, 12 V DC). It the vehicle is equipped with a glass antenna, connect it to the antenna booster power supply terminal. Never connect blue/white cable to external power amp’s power terminal. Also, never connect it to the power terminal ot the auto antenna. Otherwise, battery drain or maltunction may result. IP-BUS connectors are color-coded. Be sure to connect connectors ot the same color. Black cable is ground. This cable and other product’s ground cable (especially, high-current products such as power amp) must be wired separately. Otherwise, tire or maltunction may result it they are accidentally detached. ^Connecting the units ~) c English Connection Diagram 1. USB cable Connect to separately sold USB device. 2. Microphone Input Connect to optional microphone (CD-VM1). 3. AUX jack (3.5 0) Use a stereo mini plug cable to connect with auxiliary device. 4. Wired remote Input Hard-wired remote control adaptor can be connected (sold separately). 5. IP-BUS Input (Blue) 6. Antenna jack 7. Rear output 8. Front output 9. Subwoofer output 10.This product 11.IP-BUS cable 12.Multi-CD player (sold separately) 13.Note Depending on the kind of vehicle, the function of 3* and 5* may be different. In this case, be sure to connect 2* to 5* and 4* to 3*. 14.Connect leads of the same color to each other. 15.Cap (1*) Do not remove cap if this terminal is not in use. 16.Fuse (10 A) 17.Yellow (3*) Back-up (or accessory) 18. Yellow (2*) Connect to the constant 12 V supply terminal. 19.Fuse resister 20.Red (5*) Accessory (or back-up) 21. Red (4*) Connect to terminal controlled by ignition switch (12 V DC). 22.Black (chassis ground) Connect to a clean, paint-free metal location. 23.ISO connector Note In some vehicles, the ISO connector may be divided into two. In this case, be sure to conn...