valutazioni - , GPA:
(
)
)
Produttore : Genie
File Size : 16.06 mb
File Nome : 66a15593-ce51-40a8-9d8a-f249b0d2fb70.pdf
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
1. Keep people clear of opening while door is moving. 2. Do NOT allow children to play with opener, including wall console, remote, or wireless keypad. 3. During programming, the door opener could begin to run, so keep people and objects away from the moving door and its parts. To keep the door from moving, close the door and disconnect it from the rail carriage by pulling the Emergency Release Handle. See page 19 for Release Handle operation. LOST OR STOLEN REMOTE - CLEARING MEMORY Clearing remotes from powerhead memory will clear ALL programmed remotes and wireless keypad. NOTE: Follow the PROGRAM REMOTE TO POWERHEAD steps to re-enter remaining or new remotes. See page 9. PROGRAM 1. Press and hold SET until both lights come ON BLUE. Release button. FIG. 5-1 Remote See page 21 for battery changing instructions. Three Button 2. Lights go out and Round Remote BLUE light comes ON. PROGRAM 3. Press PROGRAMSET— + again and SET long LED flashes PURPLE. 4. Press both and simultaneously on the powerhead and hold until both LEDs flash BLUE. ROGRAMSET— + FCC and IC CERTIFIED This device complies with FCC Part 15 and RSS 210 of Industry Canada. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the PROGRAMSET— + FCC Rules. These limits are designed to provide • Verify memory is cleared. Press a remote reasonable protection against harmful interference button that was previously programmed to in a residential installation. This equipment the powerhead. Remote will not activate door generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which may be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: • Re-orient or relocate the receiver antenna. • Increase the separation between the opener and receiver. • Connect the opener into an outlet on a circuit different from that to which the receiver is connected. • Consult your local dealer. opener. • Garage door opener will operate normally using wall console. • Program remaining or new remotes as shown on page 9. Your door opener will no longer recognize any signal received from the missing remote, or any other which has not been reprogrammed to the powerhead. ©2011 The Genie Company 3/2011 16 3. Press the same button twice to toggle IntelliCode® selection from IntelliCode® 2 to IntelliCode® 1. INTELLICODE® FEATURES Other models of Genie® garage door openers, remotes, and wireless keypads use IntelliCode® 1 signals to communicate. Remote(s) provided with this unit will transmit either IntelliCode® 1 or IntelliCode® 2 signals. Remote(s) contained in this package are preset to IntelliCode® 2 and can be configured to communicate with previously installed IntelliCode® 1 openers. This dual IntelliCode® option allows one IntelliCode® 2 remote to operate different models of The Genie Company garage door openers. This new Genie® garage door opener will ONLY accept signals from a remote sending IntelliCode® 2 signals (see page 9) or a Genie® brand IntelliCode® 1 remote that has been programmed to the opener using a new IntelliCode® 2 remote (see page 10). NOTE: Other remotes not enabled with Genie® IntelliCode® 2 will not operate this opener. If you have ... Use this IntelliCode® programming One or more IntelliCode® 2 openers with a maximum 3 different openers Use IntelliCode® 2 Mixture of openers manufactured between 1997 and 2010 (IntelliCode® 1) and new IntelliCode® 2 openers Use IntelliCode® 2 and/or 1 One or more openers manufactured between 1997 and 2010 (IntelliCode® 1) Use IntelliCode® 1 NOTE: A maximum of 3 different openers can be programmed to a 3 button remote. Programming remote to previously installed IntelliCode® 1 Genie® garage door openers Remotes provided with this unit can operate other (IntelliCode® 1) models of Genie® garage door openers. The default IntelliCode® 2 setting must be changed to IntelliCode® 1. (Follow these same steps to change IntelliCode® 1 back to IntelliCode® 2.) The LED color displayed on the remote indicates the IntelliCode® mode. Red = IntelliCode® 1 / Green = IntelliCode® 2 1. Select a button on the remote that has NOT been programmed to the new powerhead. 2. Press and hold that button for 10 seconds. Both Red and Green LEDs come ON and stay ON. 10 SECS 4. Press the same button again to confirm toggle. The IntelliCode® selection for this button is set to IntelliCode® 1. 5. Take the remote to the older Genie® garage door opener and follow that opener's instructions to program a new remote. Repeat for other Genie® garage remote(s) as necessary. Red LED Green LED Three button remote AT...