|
Facilità d'uso
INSTALLER: Leave this manual with your customer upon completion of the installation. Page 1 of 4 P/ N 190-104780 REV D Page 2 of 4 P/N 190-104780 REV D IMPROPER WIRING COULD CAUSE ELECTROCUTION OR DAMAGE TO CIRCUITRY. FOLLOW LOCAL BUILDING AND ELECTRICAL CODES. WARNING WARNING DO NOT USE RADIO CONTROLS ON COMMERCIAL DOOR OPERATORS UNLESS PROPER ENTRAPMENT PROTECTION DEVICES ARE INSTALLED. CONSULT THE MANUFACTURER OF YOUR OPERATOR FOR MORE DETAILS. 831 COMMERCIAL RECEIVER WIRING INSTRUCTIONS The 831 receiver functions as a 3-button station. Three sets of isolated contacts are provided; normally open contacts for the OPEN PUSHBUTTON (terminals #3 & #4); normally open contacts for the CLOSE PUSHBUTTON (terminals #5 & #6); normally closed contacts for the STOP PUSHBUTTON (terminals #7 & #8). For special STOP circuit applications, normally open contacts (terminals #8 & #9) are available. Refer to Figure 1. Typical 4-wire 3-button stations are wired as shown in Figure 2. Number 18 gauge wire or heavier must be used for wiring the control stations and the 831 receiver to the door operator. Smaller gauge wire may cause operational problems, especially when multiple 3-button stations are used. For typical installations the 831 receiver is mounted near the door operator, away from any high voltage conduits or steel support beams. For wiring, follow the steps below and refer to Figure 3. · In the 831 receiver, connect STOP terminal #7 to CLOSE terminal #6 and to OPEN terminal #4. Use short lengths of 18 gauge wire. · In the door operator control panel, locate the wire connecting the door operator to the 3-button station COMMON. Note its location and remove. Reconnect this wire to terminal #8 in the 831 receiver. · In the 831 receiver connect terminal #7 to the terminal in the door operator control panel identified above. · In the 831 receiver connect terminal #5 to the CLOSE pushbutton terminal in the door operator control panel. · In the 831 receiver connect terminal #3 to the OPEN pushbutton terminal in the door operator control panel.. · Finish the wiring by connecting the 24 VAC to terminals #1 and #2 in the 831 receiver. FOR 115 VAC UNIT ONLY: If the 831 receiver was ordered for 115 VAC operation it has a transformer mounted on the circuit board. Connect 115 VAC to terminals #1 and #2. High voltage wires must be routed in a separate conduit from the low voltage wires. BEFORE APPLYING POWER, CHECK ALL CONNECTIONS AND INSTALL THE ANTENNA. Figure 1 Figure 2 1 2 3 4 5 6 7 8 9 POWER OPEN CLOSE STOP CAUTION 24 VOLTS AC ONLY RADIO RECEIVER TERMINAL STRIP STOP CLOSE OPEN TERMINAL STRIP TO OPERATOR 105113 WALL PUSHBUTTON STATION 105113 Figure 3 COMMERCIAL STOP COM OPEN CLOSE OPERATOR RECEIVER 831 OPEN STOP CLOSE WALL PUSH . BUTTON STATION 1 2 3 4 5 6 7 8 9 DISCONNECT POWER TO RECEIVER AND DOOR OPENER BEFORE WIRING PERMANENTLY TO PREVENT ELECTROCUTION. WARNING Page 3 of 4 P/N 190-104780 REV D The 831 receiver may be used with many different transmitters. The information below indicates how to set the coding switches in the various transmitters and the 831 receiver. IF YOU ARE USING A 8831 OCS-ECONOMY OR 831 STANDARD TRANSMITTER: Exactly match all 8 code switches in the transmitter and receiver. The code switches may be set in any random pattern of +, - and 0. IF YOU ARE USING A 8831C OCS-ECONOMY OR 733 STANDARD TRANSMITTER: These transmitters are used to control up to 3 different doors. This is accomplished by setting the selector switch on the transmitter to either A, B & C and setting the #6 coding switch in the 831 receiver . Start coding by exactly matching all 8 code switches in the transmitter and the receivers. The code switches may be set in any random pattern of +, 0 and - positions. Next, in receiver A, set code switch #6 to the + position; In receiver B set code switch # 6 to the 0 position; In receiver C set code switch # 6 to the - position. The table to the right shows the switch positions. IF YOU ARE USING A 639 STANDARD TRANSMITTER: This transmitter is used to control up to 9 different doors. This is accomplished by setting the selector switch on the transmitter to either 1, 2, 3, 4, 5, 6, 7, 8 or 9 and setting the #7 and #8 coding switches in the 831 receiver. Start coding by exactly matching all 8 code switches in the transmitter and receivers. The code switches may be set in any random pattern of +, 0 and - positions. Next, in receiver 1, set code switch #7 to + and code switch #8 +; In receiver 2, set code switch #7 to + and code switch #8 to 0. Continue setting the codes in the 831 receivers as shown in the table. IF YOU ARE USING A 535 STANDARD TRANSMITTER: This transmitter is used to control up to 27 different doors. This is accomplished by setting the selector switches to either A, B or C and either 1, 2, 3, 4, 5, 6, 7, 8 or 9 and setting the #6, #7 and #8 coding switches in the 831 receiver. Start coding by exactly matching all 8 code switches in the transmitter and receiver. Next, in receiver A1, ...
Questo manuale è adatto anche per i modelli :Cancello automatico - 831-J (111.85 kb)