valutazioni - 2, GPA: 4 ( )

Produttore : Wayne File Size : 1.07 mb File Nome : Lingua di insegnamento:

Pressing the PET LOCK button while the door is in the pet position will cause the door to close. Pressing the UP/DOWN button while the door is in the pet position will cause the door to open. NOTE: a door in the pet position is not locked and should not be used as a secured door position. 5. The wall station PROGRAM button has several functions. a. It can be used to set a custom pet position. (see below) b. It can be used to set the opener’s closing force (See Adjustment #1 Page 27). To set a custom pet position, start with the door in the closed position. 1. Operate the door then stop it at the desired height. If desired height is not achieved, the door must be returned to the closed position. 2. Press the wall station PROGRAM button until the LED turns on solid (5 sec.), or the opener power head PROGRAM SWITCH button two times. The STATUS light on the power head unit and the overhead light will flash on and off at a normal rate. 3. Press the PET POSITION button. The STATUS light on the power head and the overhead light will flash on and off three times indicating successful programming. OPENER POWER HEAD CONTROLS The PROGRAM SWITCH located in the opener power head has several functions. 1. Pressing the PROGRAM SWITCH button once, will make the STATUS light and overhead lamp turn on solid. This mode allows programming of Transmitters, Wireless Keyless Entry, and Wireless Wall Stations (see pages 19, 21, and 26). 2. Pressing the PROGRAM SWITCH button two times will make the STATUS light and overhead lamp blink on and off. This mode allows programming of a custom pet position (see above). 3. Pressing the PROGRAM SWITCH button three times will make the STATUS light and overhead lamp blink on and off with a long pause at each blink cycle. This mode allows programming of the opening force (see page 27). 4. Pressing and holding the PROGRAM SWITCH button for 10 seconds will erase all transmitters from memory. The STATUS light and overhead light will flash 3 times indicating a successful erase operation. 31 HOW TO OPERATE THE DOOR MANUALLY – Emergency Release Disconnect WARNING: The door should be fully closed if possible, weak or broken springs could allow an open door to fall rapidly. Property damage or serious personal injury could result. Do not use the manual release knob to pull the door open or closed. Do not stand near or in the path of door when using the emergency release disconnect. The opener is equipped with an emergency release recessed trolley-type disconnect system, enabling manual operation of the garage door during power failure. The trolley is disconnected from the chain by pulling down on the red release knob, allowing the garage door to be operated manually. The trolley will automatically reconnect when power is restored and door is activated. If emergency release is used, close door before operating opener. NOTE: Outside keylock emergency releases are an available accessory and are recommended for garages without a service entrance. Programming a HomeLink™ Equipped Automobile to the Power Head Unit WARNING: During programming the garage door may operate. Keep people and objects clear of the moving door to prevent door damage or possible personal injury. NOTE: Use the instructions included with your vehicle FIRST. If the Power Head Unit does not activate with the vehicle then follow the instructions listed below. Make sure you use a hand held transmitter which is already programmed to the Power head (see step 23), to perform the procedure listed below. 1. Press and hold the two outside buttons on the HomeLink™ unit until the light begins to flash rapidly (approx. 20 sec.). Release both buttons. (Do not perform this step to train additional hand-held transmitters). Note: This operation erases all previously trained transmitters. Additional transmitters must be programmed using steps 2-5 below. 2. Hold the hand held transmitter about 1” to 3” away from the HomeLink™ unit keeping the both units indicator lights in view. 3. Press and hold the hand held transmitter large center button. The transmitter’s red indicator will turn on. After 10 seconds the red indicator will blink rapidly. After 5 more seconds the red indicator will come on steady. Do not release the button. 4. While still holding the Wayne-Dalton transmitter button (red indicator on steady), immediately press and hold the desired HomeLink™ button. Keep pressing the buttons until step 5 has been completed. 5. The HomeLink™ indicator light will be blinking during the training operation. When the HomeLink™ indicator light flashes rapidly or turns off (approx. 5 to 60 seconds), both buttons may be released. The HomeLink™ light flashing rapidly or turning off indicates successful programming of the new frequency signal. Now that HomeLink™ has learned the hand held transmitter code you must program HomeLink™ to the Power Head Unit. 1. Press the PROGRAM Switch button located on the garage door Power Head Unit once. The red PROGRAM STATUS ligh...

Scarica la tua

Per scaricare, digitare 2 cifre :