valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
Spindles may be extended a minimum af 1” but not more than 4” on each side. Adjust gate sections until gate is approximately right width and adjustment holes are aligned top and bottom. Sections should fit without any distance between bars. Gate sections must not be extended any further than 4 adjustment holes from spindle ends of gate and holes must overlap at two places on both the top and bottom railing. Place one set of expansion screws and screw sockets (i and j) in top and bottom set of overlapping adjustment holes nearest hinge side of gate and second set of expansion screws and screw sockets in overlapping holes nearest locking side of gate. Tighten with screwdriver. Push stabilizing foot (p) into vertical tube. Use of stabilizing foot is optional unless one or more (maximum 4) optional extensions are used. Center gate in opening. Gaps on each side should be equal. Place hinge spindles (I) over hinge bottom posts (c), dropping them into place. Adjust latch spindles out until they fit securely into the two locking brackets. Latch spindles must be adjusted so they click under locking latch when in closed position. Space between end of gate and mounting surface should be no less than 1” and not more than 4” on each side. Check that gate can be easily opened and closed without catching. Place a spring (k) and hinge cap (d) on each hinge post. This may require some manipulation to ensure hinge posts fit and holes line up. Insert remaining screws and tighten. With wrench (q) tighten lock nuts on all spindles towards gate. WARNING: The spring must be placed OVER hinge spindle and hinge cap must be installed as directed. A protective plastic cover (h) is provided for the top latch spindle. Cut cover, remove latch spindle and put cover on. Return spindle and adjust to correct length. Safety foot To open walk through section, press down on top locking latch, lift walk through section so hinge is raised (a), and slide out of bracket. Note: The gate should always be in locked position. If gate is open and excessive pressure is applied, hinge posts are designed to break to prevent structural dama ge. To close gate, lift walk through section and position safety foot onto frame, making sure hinge has dropped down (b). To lock gate, latch spindle at top must click under locking latch. No part of gate needs lubrication. Clean by sponging with warm water and mild detergent. l• Do not use abrasive cleaners or bleach. l• If using out doors, and to help prevent rust, treat all exposed metal on gate with a rust inhibitor. Some rusting may still occur. KIDCO LIMITED WARRANTY Your KidCo product is warranted to be free from manufacturing defects for a period of one year from date of purchase under normal use and in compliance with the operating instructions. This warranty extends only to the original retail purchaser and is only valid when suppli- ed with proof of purchase. KidCo will either repair, or at our option replace, free of charge, any parts necessary to correct defects in material or workmanship during the warranty period. This warranty is complete and exclusive. The warranty expressly disclaims liability for incidental, special and consequential damages of any nature. Any implied warranty arising by operation of law shall be limited in operation to the terms of this warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above may not apply to you, This warranty gives you specific legal rights, and you may have other rights which vary from state to state. SHOULD REPAIR OR PARTS BE NECESSARY Should a repair be needed during the warranty period, ship the gate in the original carton or similar protective container (check any retail store or purchase from UPS) and send freight prepaid (we suggest UPS) to: KidCo, Inc., 1013 Technology Way, Libertyville, IL 60048. Include a note with your return address, day-time telephone number, and specify what is wrong with the product. Repairs can normally be made within 48 hours after receipt at KidCo. For additional information CALL our customer service department at (800) 553-5529. 10 ...
Questo manuale è adatto anche per i modelli :Cancello automatico - G24 (553.01 kb)