Code can easily be changed if desired. Operation: Opener activates when 4-digit code and ENTER button are pressed. If wrong numbers are accidentally pressed, correction can be made immediately. The ENTER key will transmit only the last four digits. The keypad will blink for 15 seconds after the code is transmitted. During that time you can STOP or REVERSE door travel just by pressing the ENTER key. The Multi-Function Keyless Entry can be used with any 'SMART' receiver. The keypad will illumi

THERE ARE NO OTHER USER SERVICEABLE PARTS. The 53000 Series remote control (with green battery test light) works only with door openers and light controls having a green "SRT" button and green indicator light. Instructions are given below for programming your opener to match the remote control's code. The additional remote control buttons can also activate other garage door openers and/or light controls. (Instructions for programming light products are included with those accessories.) 53000

All the codes the opener has learned will be erased. • To reprogram, repeat Steps 1, 2 and 3 for each remote control in use. Replacement Parts: 12 Volt battery -10A14; Compact remote control case, cover and Velcro strip (circuit board not included) - 41A3592; 3-Function remote control case, cover, screw (circuit board not included) - 41A3888; Visor Clip - 29C128 Select a remote control push button to operate opener Figure 2 Garage Door Opener (With Green "SRT" Button) [ M Су Çy / \ |7i

adjustment or modifications of this receiver and/or transmitter era prohibited. except lor changing (he code ¡»siting or replacing the battery THERE ABE NO OTHER USER SERVICEABLE PARTS The 53000 Series remote control works only with door openers and light controls having a green "SRT" button and green indicator light, instructions are given below for programming your opener to match the remote control's code. The additional remote control buttons can also activate other garage door openers and/

ANY number is pressed in darkness this feature allows user to press ANY number before entering the 4-digit code Power Supply: Operates from the garage door opener power with a battery b&ck-up for code memory and light-IMPORTANT NOTE: When illumination is needed, ed keyboard Unit wiU not operate without battery avoid pressing keyboard area which contains the first code number. DISCONNECT THE POWER TO THE GARAGE DOOR OPENER BEFORE BEGINNING INSTALLATION. STEP 1--SECTIONAL DOORS: Draw two intersect

28 Adjustment Step 2 Adjust the Force Force adjustment controls are located on the right side panel of the opener. Force adjustment settings regulate the amount of power required to open and close the door. The door will stop in the up direction if anything interferes with its travel. The door will reverse in the down direction if anything interferes with its travel (including binding or unbalanced doors). If the forces are set too light, door travel may be interrupted by nuisance reversals in t

If operational noise is a problem because of proximity of the opener to the living quarters, the Vibration Isolator Kit 41A3263 can be installed. This kit was designed to minimize vibration to the house and is easy to install. . Be sure that all remote control push buttons and battery indicator lights are off. 2. Remove the bell wire from the Wall Control terminals and operate from the remote control only. If this solves the problem, the Wall Control is faulty (replace), or there is an intermitt

Fasten the manual near the garage door after installation. Complies with UL 325 /11 ii "N_ regulations effective January !, 1993 I:RRFTSMRNo 1/2 HP GARAGE DOOR OPENER • Safety Precautions • Assembly • Installation • Adjustment • Care and Maintenance • Operation • Troubleshooting • Parts List Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. Contents Page Contents Page A review of safety alert symbols ................................. 2 Install the light and lens ..........................

If the plug doesn't fit into the outlet you have, contact a qualified electrician to install the proper outlet. To avoid installation difficulties, do not run the opener at this time. To prevent electrocution or fire, installation and wiring must be in compliance with local electrical and building codes. Do NOT use an extension cord, 2-wire adapter, or change the plug in any way to make it fit your outlet. Right Wrong If permanent wiring is required by your local code, refer to the following pro

Attach sprocket cover securely. Never operate opener Dispensing Carton while your hand is near the opener sprocket. Opener Sprocket Figure 2 Leave Chain and Cable Inside Dispensing Carton to Prevent Kinking. Keep Chain and CabIe Taut When Dispensing • Detach the cable loop from the carton and fasten it to the trolley with a master link from the hardware bag. See master link procedure, Figure 1. • With the trolley against the screwdriver, dispense the cable around the pulley. • Proceed back aroun