valutazioni - 2, GPA: 3
(
)
)
|
Facilità d'uso
Remove Adhesive Backing and Apply IR LED to IR Yellow RCA (Video) White RCA (Audio Left) "Y" Adapter for use with Non-Stereo Installations Item# 5 Power Connector 4 Pin Accessory Harness - Optional Dome Light (P/N:8010730) Power Source CHOKE Auxillary video display 12 VDC Power and Ground INPUT VIDEO (Yellow) Line Out-R (Red) LINE OUT Patch Cord VIDEO RCA-Female RCA Male to Male Line Out-L (White) Line Out-V (Yellow) To Secondary AV Monitor Power Harness Item #3 Power Harness Item #3 OPTIONAL PODTVT *OPTIONAL RELAY BOX TO OPTIONAL ADDITIONAL MONITOR *ANTENNA FOR WIRELESS FM MOD SIRSWB **See Antenna Note Below *NOTE: If the original relay box P/N SIRSWB is installed, it recommended that the antenna for the wireless FM Modulator be unplugged. See Figure A for antenna location. **NOTE: Extending the wireless antenna beyond its 12 inch length will cause the FM Modulator to exceed FCC limits for wireless transmission. When installing the unit position the antenna for best reception. OPTIONAL CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply voltage to the interior lights to turn them on, negative switched systems apply ground to illuminate the bulbs. To determine which system you have you must locate the wires at the dome light. On a positive switched system, with all the doors closed and the lights out, both wires at the dome light will rest at ground. When the light is activated, one of these wires will switch to +12 vdc. This is the vehicle's switching wire. On a negative switched system, with all the doors closed and the lights out, both wires at the dome light will rest at + 12vdc. When the light is activated, one of these wires will switch to ground. This is the switching wire. For positive systems, connect the purple / brown (Lamp auto) wire to the vehicle's switched wire. Then connect the red / black (lamp on) wire to a fused constant 12 volt source and the black / red (lamp common) wire to a good ground. Positive systems are commonly found on Ford vehicles. For negative systems, connect the purple / brown (Lamp auto) wire to the vehicle's switched wire. Then connect the red / black (lamp on) wire to a good ground and the black / red (lamp common) wire to fused constant 12 volt source. Negative systems are commonly found on General Motors and import vehicles. Note: Some vehicles which incorporate transistorized control of the dome light circuit, such as the 1999 Dodge Caravan, may require that the purple / brown (Lamp auto) wire be connected to the door pin switch wire, as the additional current draw of the Monitor's lights may not be supported by the output of the vehicles body control computer. Positive Switched Dome lighting To Red / black - Lamp on To 12 pin constant Black / red - Lamp common connector Purple / brown - Lamp Auto +12vdc on Monitor Factory Dome light circuit To constant +12vdc Factory Door ajar switch or Body Control computer -7 Negative Switched Dome lighting To 12 pin connector Red / black - Lamp onBlack / red - Lamp common Purple / brown - Lamp Auto To constant Factory Dome light circuit Troubleshooting: SYMPTOM: No power at Video Monitor Power but no video or sound Picture, but no sound Static on TV Stations (Tuner Version Only) No Infrared remote functions for VCP (or other components) To constant Factory Door ajar switch or Body REMEDY: -Verify +12 VDC on Red wire at 2 pin Power Harness behind video monitor. Verify ground connection with continuity test from known good ground to black wire at 2 pin Power Harness -Verify that the correct source is selected (i.e.: 1,2,3 or 4). Verify that the source is on and playing a known good media (such as a videotape). Verify connections at both ends of the source component harness. -Push and hold the volume up button until sound is heard over headphones. If problem is limited to the dash radio, verify radio is tuned to the correct channel, and that power to the wired RF modulator is on. (Refer to instructions with modulator kit). Otherwise, verify all connections per the wiring diagram on page 6. -Press Auto Program button. Then press CH up or CH down. Verify antenna mounting and connections to the tuner. Note: Due to the nature of TV signals, vehicle motion, direction the vehicle is facing, distance from the transmitter, nearby surroundings and weather may adversely affect TV reception. These conditions may result in the following: picture roll, "snowy" picture, or momentary loss of color. -Check batteries in the hand held remote (not included with this kit). Verify that the IR LED ( page 6 Wiring Diagram) is properly attached to the sensor window of the VCP (or other component). -8 For Customer Service Visit Our Website At WWW.audiovox.com Product Information, Photos, FAQ’s Owner’s Manuals 128-7257A © Copyright 2005 Audiovox Electronics Corp. 150 Marcus Blvd. Hauppau...
Questo manuale è adatto anche per i modelli :Video Car - DVD PLAYER VOD1023 (149.4 kb)
Video Car - DVD PLAYER VOD1023 P (149.4 kb)