valutazioni - 4, GPA: 3.5 ( )

Produttore : Whistler File Size : 572.1 kb File Nome : Lingua di insegnamento:

Keep the unit and all cords clear of the steering wheel, gas, brake and clutch To maintain your inverter in proper working condition, note the following important safety precautions: • MOISTURE. Keep the inverter dry. Do not expose it to moisture. Do not operate the inverter if you, the inverter, the device being operated or any other surfaces that may come in contact with any power sources are wet. Water and many other liquids can conduct electricity which may lead to serious injury or death. • HEAT. For peak efficiency, the ambient air temperature should be between 50° and 80° F. Avoid placing the inverter on or near heating vents, radiators or other sources of heat. Do not place the inverter in direct sunlight. • VENTILATION. In order to disperse the heat generated while the inverter is in operation, keep it well ventilated. While in use, maintain several inches of clearance around the top and sides of the inverter. • FUMES & GASES. Avoid using the inverter near flammable materials. Do not place the inverter in areas such as battery compartments, where fumes or gases may accumulate. 19 OPERATING PRINCIPALS OPERATION pro1200to3000w.4/30/2010 8:55 AM Page 23 For You Technical Types. 1. Basic Operating Principles: Whistler inverters work in two stages. During the first stage, the DC to DC converter increases the DC input voltage from the power source (e.g. a 12 volt battery) to 145 volts DC. In the second stage, the high voltage DC is converted to 110 volts (60 Hz AC) using advanced power MOSFET in a full bridge configuration. The result is excellent overload capability and the capacity to operate difficult reactive loads. The output waveform resulting from these conversions is a "quasi-sine wave" or a "modified sine wave" as shown on below. This stepped waveform is similar to the power generated by utilities and has a broad range of applications. The modified sine wave produced by the Inverter 20 The modified sine wave produced by your Whistler inverter has a root mean square (RMS) voltage of 110 volts. of AC voltmeters measure RMS voltage and assume that measured waveform will be a pure sine wave. Consequently, these meters will not read the RMS modified sine wave voltage correctly and, when measuring your Whistler inverter output, the meters will read about 20 to 30 volts too low. To accurately measure the output voltage of your inverter, use a true RMS reading voltmeter such as a Fluke 87, Fluke 8060A, Beckman 4410, Triplett 4200 or any multimeter identified as "True RMS." For more information on inverters see our Inverter FAQ page at whistlergroup.com A true sine wave typical of home AC outlet. 21 OPERATION SUMMARY OPERATING PRINCIPALS/SUMMARY pro1200to3000w.4/30/2010 8:55 AM Page 25 In Review. • Never attempt to operate your Whistler inverter from any power source other than a 12 volt battery or a group of batteries that total 12 volts. • Always make certain that the power cable terminal connections Negative (-) to Negative ( -) and Positive (+) to Positive (+). Check these connections frequently to ensure that they are secure. • Make certain the rated power consumption of the appliance or equipment you wish to operate is compatible with the capacity of your inverter. • If the rated power consumption of the equipment is in the range of the maximum specified wattage of your converter, test the inverter to ensure that it will operate properly. • Before attempting to use a battery charger see page 16. • Before attempting to use medical equipment see page 6. • Use the proper gauge cable (smaller the number, the larger the cable) available to connect the inverter to the power source. • When operating the inverter with the engine off, start the engine every 30 to 60 minutes and let it run for at least 10 minutes to recharge the battery. 22 • In the event of automatic the inverter OFF (O) immediately. Do not restart the inverter until the source of the problem has been identified and • To avoid battery drain, always disconnect the inverter when the vehicle is not in use for long • Do not expose the inverter to moisture. • Avoid placing the inverter near sources of heat or in direct sunlight. • When in use, make certain that the inverter is properly ventilated. • Do not use the inverter near flammable materials, fumes, or gases. • Always operate the inverter in accordance with the instructions in this manual. Failure to do so may result in property damage, personal injury, or loss of life. • While connecting the inverter to the power source, make certain that the inverter is well removed from any potential source of flammable fumes or gases. • In the event a continuous audible alarm or automatic shut off, turn the inverter OFF immediately. Do not restart the inverter until the source of the problem has been identified and corrected. 23 pro1200to3000w.4/30/2010 8:55 AM Page 27 TROUBLESHOOTING TROUBLESHOOTING PROBLEM: TV Interference Overload LED on Problem Solution Electrical interference from Add a Ferri...

Scarica la tua

Per scaricare, digitare 2 cifre :