valutazioni - 5, GPA: 4.2
(
)
)
|
Facilità d'uso
If you already have a personal OGM, you can still change your OGM when the memory is full. • Many local phone companies use Calling Party Control (CPC) to signal that a caller has hung up. Your system can recognize a CPC signal and release the line. • If memory reaches maximum capacity, while a caller is leaving a message, it stops recording and hangs up automatically. 7 5.2 Screening Calls To screen your calls, let the system answer. Listen to the caller’s message through the system’s speaker. If you decide to answer the call, pick up any phone connected to the same phone line as the system.The system stops recording and resets to answer the next call. In the event that the system continues recording, press the hook switch on the telephone momentarily. Notes: • When the lowest volume is set, the caller’s message cannot be heard. The standard voice prompts, beep tone, and recorded message should not be audible at minimum volume when any of the buttons are pressed, either. • If you pick up the phone just as the system answers, the system might not stop playing the message. If this happens, press PLAY/STOP button to stop playing the message. 5.3 Recording Message into the Mailbox You can record a message, for another member of your household, in either of the two mailboxes (Mailbox 1 or Mailbox 2). It will be played back, along with other messages, in the corresponding mailbox. To Record Message: 1. Press and hold the MAIL 1 PLAY/STOP button or MAIL 2 PLAY/STOP button. A beep will sound. 2. Record your message through the microphone in the speaker holes. 3. When your message is completed, release the button. 5.4 Playing Messages • The Message Counter will display the total number of messages in two Mailboxes.The number of messages flash rapidly after the system records new messages. • The LED of Mail 1 or Mail 2 will flash to indicate new messages received in the corresponding mailbox. 8 1. To listen to Mailbox 1 messages, press MAIL 1 PLAY/STOP button.To listen to Mailbox 2 messages, press MAIL 2 PLAY/ STOP button, the Message Counter will display the message number being played. Note: If there are no messages, the display shows “0” and you will only hear either “mailbox 1” or “mailbox 2” when you press the corresponding mailbox PLAY/STOP button. 2. The system plays each new message in sequence and announces the day and time it was recorded. 3. During message playback: • Press / TIME CHECK button to repeat the current message. • Hold down / TIME CHECK button for about two seconds to repeat the previous message. • Press / TIME SET button to skip forward to the next message. To stop message playback at any time, press PLAY/STOP button. 4. After playing all messages, the system beeps and saves the messages. The total number of messages in two Mailboxes appears on the display. 5. To replay all messages, press the corresponding mailbox PLAY/STOP button. 5.5 Deleting Messages You can delete messages individually during playback, or all at once after playback. To delete an incoming message (after listening to it), press ERASE button once during playback, “E” appears on the display. To delete all messages in the corresponding mailbox after playback, hold down ERASE button for about two seconds. “E” is flashing rapidly on the display, press the corresponding mailbox button.The system beeps and all messages in the corresponding mailbox are deleted. Note: If you hold down ERASE button before playing back all messages, the system beeps. You cannot delete the new messages until you play them all back. 9 5.6 To Reset If an AC power failure occurs, or the AC power adaptor comes out of the wall, your unit will shut down until the power is restored. If your unit is not operating properly when the power is restored, proceed with a unit reset. 1. Unplug the AC adaptor from the power outlet and telephone line from the wall jack. 2. Replace the 9 volt alkaline battery with a fresh one. 3. Plug the AC adaptor back into the power outlet. 4. Plug the telephone line back into the wall jack. 5. Record a new outgoing announcement or you can use the pre-recorded announcement. 6. Set the date and time. 6 Remote Operation While you are away from your home or office, you can access your system by remote operation. Use a touch-tone phone to enter your remote operation security code. 6.1 Operating the System from a Remote Location To use your system from a remote telephone, you must enter a 3-digit remote operation security code. The security code label is located on the bottom of the unit. 1. Dial your phone number. 2. After the system answers, wait for the outgoing message and the beep tone. Enter your remote operation security code. The unit will emit two beeps to indicate the code was entered correctly. 3. Enter a remote command. See “Remote Commands”. Notes: • If the memory is full, the system will answer calls after 10 rings, then announce “memory is full” and emit three short beeps.You can then enter the 3-digit remote code to contro...
Questo manuale è adatto anche per i modelli :Risposte automatiche - AM100 (79.4 kb)