valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
Read and understand all instructions. Thank you for purchasing the Panasonic automatic telephone answering system with full-digital memory. I------------------1 I Attach your purchase receipt here. | For your future reference Serial No._ Date of purchase_ (found on the bottom of the unit) Name and address of dealer •To order accessories, call 1-800-332-5368. 2 Contents Location of Controls .................................. 4 Display.............................................. 5 Setting Up........................................................................................6 Connection....................................................................................6 Battery Installation........................................................................7 Recording a Greeting Message ................................................8 Day and Time Adjustment ............................10 • Selecting the Number of Rings ........................12 Automatic Answering Operation ......................13 Setting the Unit to Answer Calls........................13 Listening to Messages ................................14 Erasing Messages ....................................16 Recording a Memo Message ..........................17 Remote Operation ....................................18 Setting the Security Code Number......................19 Voice Menu Operation ................................20 Direct Remote Operation..............................22 Battery Replacement..................................25 Before Requesting Help ..............................26 FCC and Other Information............................28 Important Safety Instructions..........................30 3 Location of Controls Display CODE Button (p. 19) GREETING Button (P- 9) CLOCK Button {p. 11) / ERASE Button (p. 16) ANSWER ON Button (p. 13) MEMO Button (P- 17) REPEAT Button (p. 11, 15) ALL MESSAGE/STOP Button (p. 14, 15) RINGER Selector (p. 12) VOLUME Selector (p. 14, 15) SKIP Button (p. 11, 15) MIC (Microphone) (p. 9, 17) 4 Display 'calls The battery is not installed or battery power is low. Install a new battery (p. 7, 25). CALLS') n u calls) CALLS') 1 CALLS') J 3. c I u CALLS) on The answering function is turned on and no messages are recorded. The answering function is turned off. 3 messages have been recorded. 3 messages including new message(s) have been recorded (p. 14). Memory is full. Erase some or all messages (P- 16). The unit is answering an outside call. CALL§\ _ r I L The unit is being operated from a remote phone. 5 Connection oUSE ONLY Panasonic AC ADAPTOR KX-A17. oThe AC adaptor must remain connected at all times. (It may feel warm during use. This is normal.) oTo prevent misoperation, do not connect a pulse telephone (20 pps) to the same line. 6 Battery Installation Install the included 9V size battery in the unit. If the battery power is low or the battery is not installed, “Lo” flashes. Replace with a new one. (If “Lo” flashes after installing a new battery, it will disappear after 10 seconds. Simply disconnect the AC adaptor cord and reinsert it again without removing the battery.) The new battery’s retention time is approximately 1 day for recorded messages and the clock (p. 10) during a power failure. 1 Open the cover by pushing Install the battery in the battery compartment. Snap on the terminals of the battery to the battery clip. Close the cover. £> Setting Up Recording a Greeting Message You must record a greeting message (announcement) up to 30 seconds. If a greeting message is not recorded, the unit will not answer calls. All messages (greeting, incoming, memo, etc.) are stored in digital memory. Total recording time is about 10 minutes. (The caller’s recording time is up to 1 minute.) We recommend you record a brief greeting message leaving more time in memory. 8 Press and hold (GREETING). 2 After a long beep, speak clearly 20 cm (8") away from the M1C (microphone) pressing [GREETING). oThe display counts down the remaining recording time. 0 When finished, release (GREETING). oA short beep sounds and the recorded greeting message is played. oTo change the greeting message, repeat from step 1. To check the greeting message Press and release (GREETING]. oThe recorded greeting is played, oPress (GREETING) again to stop playback. o'1 No announcement" is heard if a greeting message has not been recorded. Sample of greeting message “Hello, this is (your name and/or number). Sorry, I cannot take your call. Please leave a message after the long beep. (Your recording time is 1 minute.) Thank you." 9 O Setting Up Day and Time Adjustment Voice Day/Time Stamp: During playback a synthesized voice will announce the day and time when each message was recorded. 10 _I Press and hold (CLOCK) until a long beep is heard. oThe previously set day is heard and displayed. 2 Press (SKIP] or [REPEAT] until the current day is...