valutazioni - 4, GPA: 3.5
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
scheda madre - A8V-VM (2 mb)
scheda madre - A8V-VM (1.64 mb)
scheda madre - A8V-VM (1.2 mb)
scheda madre - A8V-VM (2.4 mb)
Facilità d'uso
Locate the CPU socket on the motherboard. A8V-VM CPU Socket 939A8V-VMRGold Arrow Before installing the CPU, make sure that the socket box is facing towards you and the load lever is on your left. 2. Unlock the socket by pressing the lever sideways, then lift it up to a 90°-100° angle. Make sure that the socket lever is lifted up to 90°-100° angle, otherwise the CPU does not fit in completely. 3. Position the CPU above the socket such that the CPU corner with the gold triangle matches the socket corner with a small triangle. 4. Carefully insert the CPU into the socket until it fits in place. The CPU fits only in one correct orientation. DO NOT force the CPU into the socket to prevent bending the pins and damaging the CPU! 5. When the CPU is in place, push down the socket lever to secure the CPU. The lever clicks on the side tab to indicate that it is locked. 1.6.3 Installing the heatsink and fan The AMD Athlon™ 64FX, Athlon™ 64X2, AMD Athlon 64™ or AMD Sempron™ processor require a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. Follow these steps to install the CPU heatsink and fan. 1. Place the heatsink on top of the installed CPU, making sure that the heatsink fits properly on the retention module base. • The retention module base is already installed on the motherboard upon purchase. • You do not have to remove the retention module base when installing the CPU or installing other motherboard components. • If you purchased a separate CPU heatsink and fan assembly, make sure that a Thermal Interface Material is properly applied to the CPU heatsink or CPU before you install the heatsink and fan assembly. CPU Fan CPU Heatsink Retention bracket Retention Module Base Retention bracket lock Your boxed CPU heatsink and fan assembly should come with installation instructions for the CPU, heatsink, and the retention mechanism. If the instructions in this section do not match the CPU documentation, follow the latter. 2. Attach one end of the retention bracket to the retention module base. 13452 3. Align the other end of the retention bracket (near the retention bracket lock) to the retention module base. A clicking sound denotes that the retention bracket is in place. Make sure that the fan and heatsink assembly perfectly fits the retention mechanism module base, otherwise you cannot snap the retention bracket in place. 4. Push down the retention bracket lock on the retention mechanism to secure the heatsink and fan to the module base. 5. When the fan and heatsink assembly is in place, connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN. A8V-VM CPU Fan ConnectorA8V-VMRGNDRotation+12VCPU_FAN Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector. A8V-VM 184-pin DDR DIMM SocketsA8V-VMRDIMM_A1DIMM_A2DIMM_B1DIMM_B2 1.7 System memory 1.7.1 Overview The motherboard comes with four 184-pin Double Data Rate (DDR) Dual Inline Memory Module (DIMM) sockets. The following figure illustrates the location of the sockets: Dual-channel mode Sockets Pair 1 DIMM_A1 and DIMM_B1 Pair 2 DIMM_A2 and DIMM_B2 1.7.2 Memory configurations You may install 128 MB, 256 MB, 512 MB, and 1 GB unbuffered ECC or non-ECC DDR DIMMs into the DIMM sockets using the memory configuration in this section. • If you install four 1 GB memory modules, the system may detect less than 3 GB of the total memory because of address space allocation for other critical functions. This limitation applies to Windows XP 32-bit version operating system since it does not support Physical Address Extension(PAE). • When using one DDR DIMM module, insert it into slot DIMM_B1 only. • When using two DDR DIMM modules, insert them into DIMM_A1 and DIMM_B1 slots. • Always install DIMMs with the same CAS latency. For optimum compatibility, we recommend that you obtain memory modules from the same vendor. Refer to the DDR400 Qualified Vendors List on the next page for details. Table 1 Recommended memory configurations Sockets Mode DIMM_A1 DIMM_A2 DIMM_B1 DIMM_B2 Single-channel (1) — — Populated — Dual-channel* (1) Populated — Populated — (2) Populated Populated Populated Populated * Use only identical DDR DIMM pairs. * For dual-channel configuration (2), you may: Install an identical DIMM pair in DIMM_A1 and DIMM_B1(blue sockets) and the other identical DIMM pair in DIMM_A2 and DIMM_B2 (black sockets) DDR400 Qualified Vendors List DIMM support Size Vendor Model Brand Side(s) Component A B C 256MB Kingston KVR333X64C25/256 Kingsto SS D3208DH1T-6 v v v 256MB Kingston KVR333X64C25/256 Hynix DS HY5DU56822BT-D43 v v v 512MB Kingston KVR333X64C25/512 Kingston DS D3208DH1T-6 v v v 512MB Kingston KVR400X64C3A/512 Hynix DS HY5DU56822BT-D43 v v v 512MB Kingston KVR400X64C3A/512 Kingston DS D3208DH1T-5 v v v 512MB Kingston KVR400X64C3A/512 Kingston SS HY5DU12822BT-D43 v v v 256MB Kingston KVR400X64C3A/256 Hynix SS HY5DU56822BT-D43 v v v 256MB Kingston KVR...