valutazioni - 5, GPA: 3.8
(
)
)
|
Facilità d'uso
. The can be restarted by turning the remote power and then ON again. liD autput. Confirm that all terminal strip connections are secure and tight. Check both in-line and built-in fuses. Both the +12Vand the Remote terminals must have +12V referenced to chassis ground. Confirm that the audio signal sourca (car radiO, equalizer, is connected and is supplying output To check if the amp is supplyinQ unrlug the cables from signal source leave them into the amp). Bnetly tap the center Pin each 0 the disconnected RCA plugs with your This should produca a noise (teedback) in your speakers. Dne clulnnel works. that all terminal strip connections are secure and tight. Check the Balance control on the head unit (or other source) to verify that it is set to its midpoint. If you are the Low Level RCA input, reverse the plugs at the amplifier (i.e., switch the L with the R). If the channels is silent switches to the other side, problem is either in the head uniVother source or the connecting cables. Welk autp.t. Readjust the Input Level Control(s) to better suit the input signal . IIDIse In tile audlD. If the noise is a ''whine· whose pitch follows the engine speed, confirm that the amplifier and any other signal sourcas (head unit, etc.) are properly grounded. If the noise is a "clicking" or ·popping" noise whose rate follows the engine speed, this usually means that the vehicle is equipped with resistor spark plugs and wires, or that the ignition is in need of service. Check the rounting of the speaker and input wires to make sure they are not adjacent to wires which interconnect lights and other accassories. If the above steps fail to improve or clear noise interterence, the system should be checked by a professional mobile audio installer. precautions Do not operate the amplifier when it is unmounted. Attach all audio system components within the automobile to prevent damage, in an accident. Do not mount this amplifier so that the wire connections are unprotected, or in a pinched condition, or likely to be darnaged by nearby objects. Before or breaking power connections in your system, the vehicle battery. Confirm that your head unit or other equipment is turned off while connecting the input jacks and speaker terminals. If lOU need to replace the power fuse, do so With a fuse identical to that supplied with the Using a fuse of a different or rating may result in damage that isn1 the manufacturer.. warranty. 4...ho""oIA..,nn.r (O,.... nl'nSIo ... ) :t- YES! Four 4-Ghm ..,e.u" wired In 1It,,-.o, wli p ... .m • 4-ohm lo.d 10 chanl'llli 01 1M ampllft.r. Mod fourChMlMI1 .mpllft.rs will work well In thl' aanfiguretion. notes Two 4-ohm IPMIt. .. , wired In PIIr,II,1 lD I bridg.d Iwo-ehlnn.! amplifi.r. will preHn! • 2-ohm mono loed to th. amplifi,r. lIOn'TWO-CHANIII!L AMPUFIIItI DO NOT 1U1'.. I-otIM IIIONO OPERATIONI AIlII'UFER DNMGE COULD RElIL T1 .... """ ....... " ... , (O,., ... ". IrIoIl... 11.,0) NOI Four +ohm .pM"''', wired In p ... n., 10. brldg..:l fuur-d1.nn.l.mpllft.r, will p ..... t • 4..,hm mono lOG til thl ..,pllll.,. MOlT FOUIt-CIlANIilEL AMP'LFEItI DO NOT".. J.OHM IIDNO OP'EltAlIONI Mft.l'lEIlIIAMAGIE COULDalULTI troubleshooting p'rotectlonclrcultru The built-in protection circuitry in the American Legacy Series amplifiers will disable the amplifier if it senses an input overload, a speaker short circuit, or extreme temperature conditions. When the circuit is activated by any of these the Protection LED will be illuminated. If this occurs, carefully inspect the system to determine the source of the problem. • If the shutdown was a result of a thermal overload condition, allow the amplifier to cool down before attempting to restart it. • If the shutdown was a result of an input overload, or speaker short circuit, be sure to correct the condition before restarting. The can be restarted by turning the remote power and then ON again. liD autput. Confirm that all terminal strip connections are secure and tight. Check both in-line and built-in fuses. Both the +12Vand the Remote terminals must have +12V referenced to chassis ground. Confirm that the audio signal sourca (car radiO, equalizer, is connected and is supplying output To check if the amp is supplyinQ unrlug the cables from signal source leave them into the amp). Bnetly tap the center Pin each 0 the disconnected RCA plugs with your This should produca a noise (teedback) in your speakers. Dne clulnnel works. that all terminal strip connections are secure and tight. Check the Balance control on the head unit (or other source) to verify that it is set to its midpoint. If you are the Low Level RCA input, reverse the plugs at the amplifier (i.e., switch the L with the R). If the channels is silent switches to the other side, problem is either in the head uniVother source or the connecting cables. Welk autp.t. Readjust the Input Level Control(s) to better suit the input signal . IIDIse In tile audlD. If the noise is a ''whine· whose pitch follows the engine spe...
Questo manuale è adatto anche per i modelli :Avtousiliteli - LA-1089 (1.66 mb)
Avtousiliteli - LA-1400 (1.66 mb)
Avtousiliteli - LA-1889 (1.66 mb)
Avtousiliteli - LA-2389 (1.66 mb)