valutazioni - 2, GPA: 3.5
(
)
)
|
Facilità d'uso
If you want to link the unit's power with the ignition, connect the ignition cable to a power source that can be turned on and off with the ignition key. • If the fuse blows, first make sure that the cables have not caused a short circuit, then replace the old fuse with one with the same rating. • Do not let unconnected cables or terminals touch metal on the car or anything else conducting electricity. To prevent short circuits do not remove the caps from unused terminals or from the ends of the unconnected cables. • Connect the speaker cables correctly to the terminals to which they correspond. The unit may receive damage or fail to work if you share the -cables and/or ground them to any metal part in the car. • After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. • Insulate unconnected cables with vinyl tape or other similar material. • During use, the surface temperature of this unit will become high, therefore it should not be mounted where anything sensitive to the heat, such as people or resins, would come into contact with it. • Do not install the unit under the carpet. Otherwise heat build-up occurs and the unit may be damaged. • Install this unit in a location which allows heat to easily dissipate. Once installed, do not place any object on top of the unit. • Install the unit securely in a location that does not interfere with driving. English 3 Installation n Connecting Cables toTerminals 2WARNING If you connect the ignition cable (red) and the battery cable (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those cables to the power source running through the fuse box. BATT ACC BATT ACC ILLUMI P.CONT TEL MUTE ANTENNA INPUT POWER SUB WOOFER REAR SPEAKER FRONT SPEAKER DAB CHANGER SLAVE UNIT TV MONITOR FM ANTENNA BATT ACC PREOUT REAR/NON-FAD FRONT 12 34 56 78 12 34 56 78 Wiring harness (5.5m) (Accessory5) Rear left output (White) / Non-fading left output (White) Rear right output (Red) / Non-fading right output (Red) Front left output (White) Front right output (Red) FM/AM antenna input Battery cable (Yellow)+12V Ignition cable (Red)+12V Automatic illumination control cable (Orange) Ground cable (Black) - (To car chassis) Connect to the terminal that is grounded when either the telephone rings or during conversation. Power control cable (Blue/ White) TEL mute cable (Brown) To connect the KENWOOD navigation system, consult your navigation manual. NOTE Antenna Cord (Accessory6) Route wiring away from power circuitry to avoid noise. NOTE Antenna Cord (ISO) Antenna Conversion Adaptor (ISO–JASO) (Accessory8) When using the optional power amplifier, connect to its power control terminal. Fuse (10A) Fuse (3A) (5.5m) Do not put anything into the fuse holder. NOTE Connector B Connector A Connect to control unit power supply terminal. If no connections are made, do not let the cable come out from the tab. 4 English Connecting the ISO Connector or the ISO connectors ou drive. Make e the proper connections to or the wiring harness If the ISO connector , make the 2WARNING BATT ACC BATT ACC BATT ACC Unit Control unit Vehicle Ignition cable (Red) A–7 Pin (Red) A–4 Pin (Yellow) 1 (Default setting) The A-7 pin (red) of the vehicle's ISO connector is linked with the ignition, and the A-4 pin (yellow) is connected to the constant power supply. BATT ACC BATT ACC BATT ACC Unit Control unit Vehicle Ignition cable (Red) A–7 Pin (Red) A–4 Pin (Yellow) 1 (Default setting) The A-7 pin (red) of the vehicle's ISO connector is linked with the ignition, and the A-4 pin (yellow) is connected to the constant power supply. Battery cable (Yellow) 2 The A-7 pin (red) of the vehicle's ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition. A–7 Pin (Red) Ignition cable (Red) Connector Function Guide Pin Numbers for ISO Connectors Cable Colour Functions External Power Connector A–4 Yellow Battery A–5 Blue/White Power Control A–6 Orange Dimmer A–7 Red Ignition (ACC) Speaker Connector B–1 Purple Rear Right (+) B–2 Purple/Black Rear Right (–) B–3 Gray Front Right (+) B–4 Gray/Black Front Right (–) B–5 White Front Left (+) B–6 White/Black Front Left (–) B–7 Green Rear Left (+) B–8 Green/Black Rear Left (–) Vehicle BATT ACC BATT ACC BATT ACC Unit A–4 Pin (Yellow) Control unit Battery cable (Yellow) 3 The A-7 pin (red) of the vehicle's ISO connector is not connected to anything, whilst the A-4 pin (yellow) is connected to the constant power supply (or both the A-7 (red) and A-4 (yellow) pins are connected to the constant power supply). Connect to a power source Ignition cable that can be turned on and | (Red) off with the ignition key. Battery cable (Yellow) Control unit UnitVehicle A–4 Pin (Yellow) BATT BATT BATT English 5 Installation n When the control unit is the KVC-1000 Control unit (optional) KVC-1000 FM•AM TUNER 44W . 4 AMPLIFIER HIDEAWAY UNIT ANTENNA INPUT ...