Log:
Scaricare : 34   File Size : 2 mb   Produttore : Kicker  
Categoria : Avtousiliteli
@name@name@name@name

. as easy as 1, 2, 3 1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The controls on the top of the amplifier need to be accessible for adjustment. Make sure there are no items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws

Scaricare : 11   File Size : 343 kb   Produttore : Kicker  
Categoria : Avtousiliteli
@name@name@name

Amplifier Serial Number: __________________________ Installation 1. Mounting Choose a structurally sound location to mount your Kicker amplifier. Make sure there are no items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifier. 2. Wiring

Scaricare : 60   File Size : 1 mb   Produttore : Cadence  
Categoria : Avtousiliteli

Scaricare : 24   File Size : 2 mb   Produttore : Cadence  
Categoria : Avtousiliteli

Scaricare : 9   File Size : 627 kb   Produttore : ARC Audio  
Categoria : Avtousiliteli
@name

This warranty gives you specific legal rights, and you may have other rights, which vary from state to state. This warranty applies to products sold and used in the United States of America. In all other countries please contact your distributor For warranty and non-warranty repairs, send to: ARC Audio 4719 Green Leaf Cr. #4 Modesto CA, 95356 _ 209-543-8706 CARC AUDIO Thankyou for purchasing an ARC Audio Hi-Performance Amplifier. This ARC Audio amplifier uses a Full Range Class D architec

Scaricare : 8   File Size : 979 kb   Produttore : Directed Audio  
Categoria : Avtousiliteli
@name@name@name@name@name@name

All rights reserved. Sealed Example High-Pass Set at 30Hz In this example, the frequency has been increased to 30 Hz Up to 6 dB of boost is capable at this frequency With +6dB of boost, the woofer has more output down to 23 Hz the overall usable output is increased Figure 8 Figura 8 Abbildung 8 Figure 9 Figura 9 Abbildung 9 AMPLIFIeR WIRInG Power Connections • Power connections accept up to 4 AWG wire • 4 AWG power and ground wire recommended for optimal performance • Connect 12V+ to the battery

Scaricare : 19   File Size : 979 kb   Produttore : Directed Audio  
Categoria : Avtousiliteli
@name@name@name@name@name@name

AmplifierMODELXTR2502XTR5002OWNER'S MANUAL AmplifierMODELXTR2502XTR5002OWNER'S MANUAL Contents english 1 Francais 19 espanol 35 Deutsch 51 Italiano 67 Portugues 83 Introduction 2 What’s in the Box 2 Practice safe sound™ 2 end Panel Layouts 3 CeA specifications 4 specifications 5 Amplifier settings 6 signal Input and output Configurations 6 Input Gain 6 Line output Configurations 6 Internal Crossover Configurations, Flat (full range) 6 Crossover switch 6 Low-Pass Crossover 6 High-Pass Crossover 7

Scaricare : 6   File Size : 995 kb   Produttore : Orion Car Audio  
Categoria : Avtousiliteli
@name@name@name@name@name@name

All rights reserved. Amplifier Top Plate PowerThermalProtection Figure 11 Figura 11 Abbildung 11 Troubleshooting Tips Symptom Probable Cause Action To Take no output Low or no remote turn-on Check remote turn-on voltage at voltage amplifier and repair as needed Fuse blown Check power wire's integrity and check for speaker shorts Fix as needed and replace fuse Power wires not connected Check power wire and ground connections and repair or replace as needed Audio input not connected Check RCA conn

Scaricare : 7   File Size : 995 kb   Produttore : Orion Car Audio  
Categoria : Avtousiliteli
@name@name@name@name@name@name

REM -this terminal turns on the amplifier when (+) 12 volt is applied Connect it to the remote turn on lead of the head unit or signal source If a (+) 12 volt remote turn lead is not available, a Remote Power Adapter (P/n oRRPA) can be used to supply a remote turn on signal Do not connect this terminal to constant (+) 12 volt 3. GND -power return connection Connect this terminal directly to the sheet metal chassis of the vehicle, using the shortest wire necessary to make this connection Always u

Scaricare : 13   File Size : 995 kb   Produttore : Orion Car Audio  
Categoria : Avtousiliteli
@name@name@name@name@name@name

All rights reserved. amplifier For optimal results, mount the amplifier with as much clearance as possible this type of mounting will yield the best cooling due to the convection effect of the amplifier chassis General Precautions and Installation Tips WARNING! Be careful not to cut or drill into gas tanks, fuel lines, brake lines, hydraulic lines, vacuum lines, or electrical wiring when working on your vehicle Disconnect the vehicle’s ground wire at the battery before making or breaking connect





categorie