СН/В. СН) Используется для установки частоты среза высокочастотного фильтра. (4) Регулятор В.СН LPF FREQUENCY Используется для установки частоты среза низкочастотного фильтра. (6) Регулятор SUB.CH LPF FREQUENCY. Используется для регулировки частотного диапазона, воспроизводимого SUB-усилителем. (7) Переключатель INPUT SELECTOR (АВ/А) Этот переключатель используется для переключения входного сигнала усилителя В. - Положение АВ: Сигнал со входа А воспроизводится через усилитель А, а со в

(SP) Seleccione "FLAT" para una gama de frecuencia del compleate. (Eng) Select "LOW" for a low frequency range. (FR) Choisissez l'"LOW" pour une gamme de basse fréquence. (IT) Selezionare "LOW" per la risposta delle frequenze basse. (D) Wählen Sie "LOW" für eine Niederfrequenzstrecke vor. (SP) Seleccione el "LOW" para una gama de la frecuencia baja. (Eng) Select "HIGH" for a high frequency range. (FR) Choisissez la "HIGH" pour une gamme à haute fréquence. (IT) Selezionare "HIGH" per la r

Terminal cover .... .... ¦ RCA cable or Speaker level input connection ¦ Power wire and Speaker wire connection ¦ Remote cable connection (KAC-7252 only) Remote cable Remote controller Genuine-accessory car stereo (No line output center unit etc.) ACC Battery Car fuse box • RCA cable Connections • Speaker level input Connections Cable Color of the connector Left 9 White · White/Black Right 9 Gray · Gray/Black Power control wire 2CAUTION • Before connecting the remote controller cables, always se

Поворачивайте регулятор [Громкость], пока не отобразится необходимый элемент, а потом нажмите на регулятор. Выберите “Music” > элемент. 3 Войдите в режим пропуска при поиске Нажмите кнопку [SEARCH MODE]. 4 Поиск элемента Тип операции Операция Перемещение между элементами Поверните регулятор [Громкость]. Выбор элемента Нажмите на регулятор [Громкость]. Пропуск при поиске Нажмите кнопку [DISP] или [TI]. Удерживайте кнопку не менее 3 секунд или дольше, тогда пропускаются 10% композиций независимо о

• Do not install near the dashboard, rear tray, or air bag safety parts. • The installation to the vehicle should securely fasten the unit to a place in which it will not obstruct driving. If the unit comes off due to a shock and hits a person or safety part, it may cause injury or an accident. • After installing the unit, check to make sure that electrical equipment such as the brake lamps, turn signal lamps and windshield wipers operate normally. Self-tapping screw (o4 . 16 mm) Installation bo

7 ID NUMBER switch Sets an amp identification number (ID) to be used for amplifier control from the Center Unit. Assign ID Number "0" to an amplifier when you use it as the Master amplifier. Assign ID Numbers "1" to "7" to amplifiers when you use them as Slave amplifiers. Do not duplicate these numbers. NOTE After you have changed ID numbers of amplifiers, turn Off the POWER switch of the Center Unit and turn it On again. 8 TO H/U terminal After you have set the Master amplifier, connect it to t

• After installation, check that the brake lamps, winkers, and wipers work properly. NOTE • Do not connect cables and leads to both RCA cable input jacks and the speaker level input terminals simultaneously, for this may cause malfunction or damage. A channel Left speaker A channel Right speaker B channel Right speaker B channel Left speaker A channel Speaker (Bridged) B channel Speaker (Bridged) A channel input B channel input Terminal cover ¦ Power wire and Speaker wire connection • RCA cable

Familiarity with installation and operation procedures will help you obtain the best performance from your new power amplifier. FOR YOUR RECORDS Record the serial number found on the bottom of the unit in the spaces designated on the warranty card and in the space provided below. Refer to the model and serial numbers whenever you call upon your KENWOOD dealer for information or service on this product. Model KAC-8200 Serial number _ CARE & MAINTENANCE • The power source of this unit is excl

. • Las siguientes operaciones desconectan la linea: -Conecte un dispositivo USB. • El nombre de la persona que llama se mostrara si ya se ha registrado en la agenda telefonica. Rechazo de una llamada entrante Pulse el boton [SRC] o el boton [ ] / [PLAY MODE] durante al menos 1 segundo. Durante una llamada Desconexion de una llamada Pulse el boton [SRC] o el boton [ ] / [PLAY MODE] durante al menos 1 segundo. Cambio al modo privado Pulse el boton [38]. Alterna entre conversacion privada (“PRIVAT

@1 B.R.F. FREQUENCY control Sets the rejection frequency when the "BRF" switch is set to "-6dB"/"-12dB". (page 8) .............................................................................................................................. ...................................................................................................................................................................................................................................................................